Cadillac Vehicle Models XT5 2017-present
Cadillac Vehicle Models XT5 2017-present Torque Specifications
Complete Cadillac Vehicle Models XT5 2017-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
2.0l Engine
Torque specifications for 2.0L Engine
2.0l Engine
Torque specifications for 2.0L Engine
Cylinder Head
1 Cylinder Head Bolts
M12 x 1.75
1
Cylinder Head Bolts
M12 x 1.75
Torque Specification
1. 22 ft-lbs (30 N·m)
2. 90°
3. 90°
Important Notes
Torque-to-yield bolts. Follow specified tightening sequence. Two 90 degree angle steps after initial torque
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
3.67 ft-lbs (5 N·m)
Important Notes
Tighten evenly to prevent leaks. Inch-lbs converted to ft-lbs for consistency.
3 Rocker Arms/Shafts Bolts
M8 x 1.25
3
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper alignment of the rocker arms. Start by lightly tightening, then torque in two steps following a specified pattern.
4 Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.5
4
Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten in a criss-cross pattern.
5 Camshaft Bearing Cap Bolts
M8 x 1.25
5
Camshaft Bearing Cap Bolts
M8 x 1.25
Torque Specification
1. 7 ft-lbs (10 N·m)
2. 18 ft-lbs (25 N·m)
Important Notes
Tighten in multiple steps to prevent cam distortion. Consult service manual for exact pattern.
6 Spark Plugs
M14 x 1.25
6
Spark Plugs
M14 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper thread engagement. Use a spark plug socket.
Engine Block
1 Main Bearing Bolts
M10 x 1.5
1
Main Bearing Bolts
M10 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m)
2. 70°
Important Notes
Torque in steps, using an angle meter or angle wrench.
2 Oil Pan Bolts
M6 x 1.0
2
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten evenly to prevent leaks. Inch-lbs converted to ft-lbs for consistency.
3 Oil Filter Housing Bolt
M8 x 1.25
3
Oil Filter Housing Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper O-ring placement.
4 Oil Drain Plug Bolt
M14 x 1.5
4
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Always use a new crush washer. Overtightening can damage the pan.
5 Water Pump Bolts
M8 x 1.25
5
Water Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper sealing of the water pump gasket.
Rotating Assembly
1 Connecting Rod Nuts
M9 x 1.25
1
Connecting Rod Nuts
M9 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 55°
Important Notes
Use an angle meter or angle wrench. Ensure connecting rod cap is properly aligned. Two-step torque with angle
2 Flywheel Bolts
M10 x 1.5
2
Flywheel Bolts
M10 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Use new bolts. Ensure flywheel is properly aligned before torquing.
3 Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
3
Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m)
2. 70°
Important Notes
Use a new bolt. Securely counterhold the pulley while torquing. This bolt is tightened to a specified value and then by angle. Use a new bolt
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper tensioner alignment during installation.
2 Timing Chain Guide Mounting Bolts
M6 x 1.0
2
Timing Chain Guide Mounting Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Ensure correct guide alignment. Values are an estimate, consult service manual
3 Camshaft Sprocket Bolt
M10 x 1.25
3
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure proper alignment of the camshaft sprocket.
Intake Exhaust
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten in a criss-cross pattern to prevent leaks. Inch-lbs converted to ft-lbs for consistency
2 Throttle Body Bolts
M6 x 1.0
2
Throttle Body Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to prevent vacuum leaks. Inch-lbs converted to ft-lbs for consistency.
3 EGR Valve Bolts
M8 x 1.25
3
EGR Valve Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure proper sealing to prevent leaks.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to avoid fuel leaks. Inch-lbs converted to ft-lbs for consistency
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure O-rings are properly positioned. Inch-lbs converted to ft-lbs for consistency.
3 High Pressure Fuel Pump Mounting Bolts
M8 x 1.25
3
High Pressure Fuel Pump Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment and sealing. Value is estimated, consult service manual.
Electrical System
1 Ignition Coil Bolt
M6 x 1.0
1
Ignition Coil Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure coils are properly positioned. Inch-lbs converted to ft-lbs for consistency.
2 Coolant Temperature Sensor Torque
M12 x 1.5
2
Coolant Temperature Sensor Torque
M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper sealing to avoid coolant leaks. Value is estimated, consult service manual.
Cooling System
1 Water Pump Pulley Bolts
M6 x 1.0
1
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to ensure proper pulley fit. Inch-lbs converted to ft-lbs for consistency.
2 Thermostat Housing Bolts
M6 x 1.0
2
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to prevent coolant leaks. Inch-lbs converted to ft-lbs for consistency.
Accessory Drive
1 Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.5
1
Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper tensioner alignment. This value is an estimate and can vary; consult the service manual.
2 Drive Belt Idler Pulley Bolt
M10 x 1.5
2
Drive Belt Idler Pulley Bolt
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure idler pulley is properly aligned. This value is an estimate and can vary; consult the service manual.
3.6l Engine
Torque specifications for 3.6L Engine
3.6l Engine
Torque specifications for 3.6L Engine
Cylinder Head
1 Cylinder Head Bolts
M12 x 1.75
1
Cylinder Head Bolts
M12 x 1.75
Torque Specification
1. 22 ft-lbs (30 N·m)
2. 90°
3. 70°
Important Notes
Use a proper tightening sequence. Torque-to-yield bolts. Additional angle tightening is critical.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper rocker arm alignment before torquing.
3 Camshaft Sprocket Bolt
M10 x 1.5
3
Camshaft Sprocket Bolt
M10 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure the camshaft sprocket is aligned before tightening.
Engine Block
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Follow the specified tightening sequence. These bolts are critical for crankshaft alignment and bearing clearance.
2 Oil Pan Bolts
M6 x 1.0
2
Oil Pan Bolts
M6 x 1.0
Torque Specification
9 in-lbs (12 N·m)
Important Notes
Use proper tightening sequence to ensure an even seal and to avoid damaging the oil pan. Use a new gasket
3 Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
3
Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure the crankshaft pulley/harmonic balancer is properly seated before tightening.
4 Oil Filter Housing Bolt
M8 x 1.25
4
Oil Filter Housing Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure a new O-ring is used, and the surfaces are clean before tightening.
5 Oil Drain Plug Bolt
M14 x 1.5
5
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new drain plug washer if needed.
6 Timing Cover Bolts
M6 x 1.0
6
Timing Cover Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a proper tightening sequence to ensure even pressure and proper sealing. Use a new gasket.
7 Knock Sensor Bolt
M8 x 1.25
7
Knock Sensor Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Clean the surfaces before install.
Connecting Rods
1 Connecting Rod Nuts
M9 x 1.25
1
Connecting Rod Nuts
M9 x 1.25
Torque Specification
43 ft-lbs (58 N·m)
Important Notes
Ensure proper bearing clearance and proper orientation of the connecting rod cap before torquing.
Intake System
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
9 in-lbs (10 N·m)
Important Notes
Follow the specified tightening sequence (refer to service manual). Use a new gasket.
2 Throttle Body Bolts
M6 x 1.0
2
Throttle Body Bolts
M6 x 1.0
Torque Specification
9 in-lbs (10 N·m)
Important Notes
Ensure throttle body is properly seated on the intake manifold.
3 EGR Valve Bolts
M8 x 1.25
3
EGR Valve Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Make sure the mating surface is cleaned and that a new gasket is used if necessary.
Exhaust System
1 Exhaust Manifold/Headers Bolts
M8 x 1.25
1
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use a new exhaust manifold gasket.
2 Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
2
Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even pressure. Use a new gasket.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
9 in-lbs (10 N·m)
Important Notes
Ensure fuel rail is properly seated and injectors are aligned correctly.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
9 in-lbs (10 N·m)
Important Notes
Ensure the injector O-rings are properly lubricated before installing and that the injector is seated correctly.
Cooling System
1 Water Pump Bolts
M8 x 1.25
1
Water Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Make sure that a new water pump gasket is used. Follow a tightening pattern to ensure even pressure is applied.
2 Water Pump Pulley Bolts
M6 x 1.0
2
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
9 in-lbs (10 N·m)
Important Notes
Ensure the pulley is correctly aligned with the water pump.
3 Thermostat Housing Bolts
M6 x 1.0
3
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
9 in-lbs (10 N·m)
Important Notes
Make sure that a new thermostat and gasket is used if necessary.
4 Engine Coolant Temperature Sensor Fitting
M10 x 1.0
4
Engine Coolant Temperature Sensor Fitting
M10 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure no thread damage or leaks.
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure correct spark plug gap before installation.
2 Ignition Coil Bolt
M6 x 1.0
2
Ignition Coil Bolt
M6 x 1.0
Torque Specification
9 in-lbs (10 N·m)
Important Notes
Ensure the ignition coil is properly seated.
Accessory Drive
1 Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.5
1
Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Make sure tensioner is aligned before tightening.
2 Drive Belt Idler Pulley Bolt
M10 x 1.5
2
Drive Belt Idler Pulley Bolt
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the idler pulley is properly seated before tightening.
Sensor System
1 Crankshaft Position Sensor (CKP) Bolt
M6 x 1.0
1
Crankshaft Position Sensor (CKP) Bolt
M6 x 1.0
Torque Specification
9 in-lbs (10 N·m)
Important Notes
Proper torque is essential for accurate sensor readings. Do not overtighten.
2 Camshaft Position Sensor (CMP) Bolt
M6 x 1.0
2
Camshaft Position Sensor (CMP) Bolt
M6 x 1.0
Torque Specification
9 in-lbs (10 N·m)
Important Notes
Ensure correct seating of the CMP sensor. Do not overtighten.
Flywheel
1 Flywheel Bolts
M10 x 1.5
1
Flywheel Bolts
M10 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Use a new set of flywheel bolts. Ensure that the flywheel is fully seated before tightening.
9t65 Transmission
Torque specifications for 9t65 Transmission
9t65 Transmission
Torque specifications for 9t65 Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M12 x 1.75
1
Transmission Mounting Bolts
M12 x 1.75
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment before tightening. Verify bolt size for your specific application.
Transmission Case
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even sealing. Overtightening can cause leaks.
2 Transmission Drain Plug
M18 x 1.5
2
Transmission Drain Plug
M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new sealing washer when installing the drain plug. Do not overtighten.
3 Transmission Fill Plug
M18 x 1.5
3
Transmission Fill Plug
M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new sealing washer when installing the fill plug. Do not overtighten.
Bellhousing
1 Bellhousing Bolts (M10)
M10 x 1.5
1
Bellhousing Bolts (M10)
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment before tightening. Verify bolt size for your specific application.
2 Bellhousing Bolts (M12)
M12 x 1.75
2
Bellhousing Bolts (M12)
M12 x 1.75
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Ensure proper alignment before tightening. Verify bolt size for your specific application.
Transmission Electronics
1 Transmission Control Module (TCM) Mounting Bolts
M6 x 1.0
1
Transmission Control Module (TCM) Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Do not overtighten, as this can damage the TCM housing. Value is an estimate
2 Transmission Range Sensor Bolts
M6 x 1.0
2
Transmission Range Sensor Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure correct sensor position before tightening. Value is an estimate.
3 Transmission Speed Sensor Bolt(s)
M6 x 1.0
3
Transmission Speed Sensor Bolt(s)
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure proper sensor seating before tightening. Value is an estimate.
Transmission Cooling
1 Transmission Cooler Line Fittings
M16 x 1.5
1
Transmission Cooler Line Fittings
M16 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure fittings are properly seated before tightening. Do not overtighten.
Body
Torque specifications for Body
Body
Torque specifications for Body
Wheels And Tires
1 Wheel Lug Nuts
M14 x 1.5
1
Wheel Lug Nuts
M14 x 1.5
Torque Specification
140 ft-lbs (190 N·m)
Important Notes
Tighten lug nuts in a star pattern. Ensure proper seating of the wheel before applying full torque.
Fuel System
1 Fuel Tank Strap Bolts
M10 x 1.5
1
Fuel Tank Strap Bolts
M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the fuel tank is properly supported before removing or tightening bolts. Do not overtighten.
2 Fuel Filler Neck Bolts
M8 x 1.25
2
Fuel Filler Neck Bolts
M8 x 1.25
Torque Specification
62 ft-lbs (84 N·m)
Important Notes
Ensure proper alignment of the filler neck before tightening bolts. Check for leaks after installation.
Body Panels
1 Door Hinge Bolts (Body Side)
M10 x 1.5
1
Door Hinge Bolts (Body Side)
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure door is properly aligned before fully tightening the bolts. May require adjustment after installation.
2 Fender Mounting Bolts (Upper)
M6 x 1.0
2
Fender Mounting Bolts (Upper)
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Estimated value based on typical M6 body panel bolt. Tighten evenly to avoid panel distortion.
3 Fender Mounting Bolts (Lower)
M8 x 1.25
3
Fender Mounting Bolts (Lower)
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on typical M8 body panel bolt. Tighten evenly to avoid panel distortion.
4 Hood Hinge Bolts
M8 x 1.25
4
Hood Hinge Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure hood is aligned properly before tightening. Check hood alignment and operation after tightening.
5 Headlight Mounting Bolts
M6 x 1.0
5
Headlight Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Do not overtighten, as this can damage the headlight housing. Use caution.
6 Taillight Mounting Bolts
M6 x 1.0
6
Taillight Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Do not overtighten, as this can damage the taillight housing. Use caution.
7 Bumper Cover Mounting Bolts
M8 x 1.25
7
Bumper Cover Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on typical M8 bumper cover bolt. Verify fit after tightening.
8 Bumper Cover Mounting Screws
M6 x 1.0
8
Bumper Cover Mounting Screws
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Estimated value based on typical M6 bumper cover screw. Do not overtighten.
9 Grille Mounting Bolts
M6 x 1.0
9
Grille Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Do not overtighten to avoid damage. Ensure proper grille alignment.
10 Side Mirror Mounting Bolts
M8 x 1.25
10
Side Mirror Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure mirror is properly positioned before tightening. Check for proper function after installation.
Electrical Components
1 Body Control Module (BCM) Mounting Bolts
M6 x 1.0
1
Body Control Module (BCM) Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Do not overtighten. Ensure proper seating of the BCM.
Interior Components
1 Interior Trim Panel Screws
M5 x 0.8
1
Interior Trim Panel Screws
M5 x 0.8
Torque Specification
3.7 ft-lbs (5 N·m)
Important Notes
Estimated value based on typical M5 interior trim screw. Do not overtighten to avoid damage.
2 Interior Trim Panel Bolts
M6 x 1.0
2
Interior Trim Panel Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Estimated value based on typical M6 interior trim bolt. Do not overtighten to avoid damage.
Roof System
1 Roof Rack Mounting Bolts
M8 x 1.25
1
Roof Rack Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the roof rack is properly aligned before tightening. May require adjustment after installation.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Caliper Assembly
1 Brake Caliper Bolts
M12 x 1.75
1
Brake Caliper Bolts
M12 x 1.75
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
These bolts secure the caliper to the mounting bracket. Ensure bolts are clean and lightly lubricated before assembly. Inspect for wear and replace if needed.
2 Brake Hose Banjo Bolt (Caliper Side)
M10 x 1.0
2
Brake Hose Banjo Bolt (Caliper Side)
M10 x 1.0
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Secures the brake line to the caliper using a banjo fitting. Use new crush washers and ensure the fitting is correctly aligned to prevent leaks.
3 Brake Caliper Bleeder Screw
M7 x 1.0
3
Brake Caliper Bleeder Screw
M7 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Used for bleeding the brake system. Do not over tighten as the bleeder screw can be easily damaged. Ensure the threads and sealing surfaces are clean.
4 Anti-Rattle Clip Bolt/Screw
M6 x 1.0
4
Anti-Rattle Clip Bolt/Screw
M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Secures anti-rattle clips to caliper or bracket. Torque to specification to eliminate brake noise and prevent component failure. This value is estimated based on similar applications.
Caliper Bracket
1 Brake Caliper Mounting Bracket Bolts
M14 x 1.5
1
Brake Caliper Mounting Bracket Bolts
M14 x 1.5
Torque Specification
129 ft-lbs (175 N·m)
Important Notes
These bolts attach the caliper bracket to the steering knuckle. It is critical for proper alignment and braking function. Use new bolts if recommended by the manufacturer.
Rotor Drum
1 Brake Disc/Drum Retaining Bolts
M8 x 1.25
1
Brake Disc/Drum Retaining Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts secure the rotor or drum to the hub. Do not over tighten. These may be screws and not bolts depending on the vehicle.
Brake Lines
1 Brake Hose Bracket Bolts
M6 x 1.0
1
Brake Hose Bracket Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
These bolts secure the brake hose brackets to the chassis and suspension components. Be careful not to over-tighten.
Parking Brake
1 Parking Brake Cable Bracket Bolts
M8 x 1.25
1
Parking Brake Cable Bracket Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts secure the parking brake cable housing to the body and chassis. Check for proper cable routing after installation.
Abs System
1 Wheel Speed Sensor Bolt
M6 x 1.0
1
Wheel Speed Sensor Bolt
M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
These bolts secure the wheel speed sensors to the hub assembly. Do not over-tighten. This value is estimated based on similar applications.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine Interface
1 Flywheel Bolts
M12 x 1.25
1
Flywheel Bolts
M12 x 1.25
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensures proper clamping force to transfer engine torque effectively. Use a new set of bolts for proper torque.
Transmission
1 Transmission Mounting Bolts
M10 x 1.5
1
Transmission Mounting Bolts
M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Securely mounts the transmission to the engine or chassis. Ensure the transmission is properly aligned before tightening.
2 Transmission Oil Pan Bolts
M6 x 1.0
2
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Bolts should be tightened in a criss-cross pattern to ensure even pressure on the gasket. This value is converted from inch pounds to foot pounds, original spec is 106 inch-lbs.
3 Transmission Drain and Fill Plugs
M18 x 1.5
3
Transmission Drain and Fill Plugs
M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Proper torque prevents leaks from the drain and fill plugs. Use a new sealing washer if possible.
4 Transmission Output Shaft Nut
M24 x 1.5
4
Transmission Output Shaft Nut
M24 x 1.5
Torque Specification
120 ft-lbs (160 N·m)
Important Notes
This nut secures the output flange or yoke to the transmission. Estimated value; verify with specific service manual.
Transfer Case
1 Transfer Case Mounting Bolts
M12 x 1.75
1
Transfer Case Mounting Bolts
M12 x 1.75
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Securely mounts the transfer case to the transmission or frame. Estimated value; verify with specific service manual.
2 Transfer Case Drain and Fill Plugs
M18 x 1.5
2
Transfer Case Drain and Fill Plugs
M18 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Proper torque prevents leaks from the drain and fill plugs. Use a new sealing washer if possible.
3 Transfer Case Output Shaft Nut
M22 x 1.5
3
Transfer Case Output Shaft Nut
M22 x 1.5
Torque Specification
120 ft-lbs (160 N·m)
Important Notes
This nut secures the output flange or yoke to the transfer case. Estimated value; verify with specific service manual.
Driveshaft
1 Propeller/Drive Shaft Bolts
M10 x 1.25
1
Propeller/Drive Shaft Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Bolts that connect the driveshaft to the transmission/transfer case and differential. Tighten in a cross pattern.
2 Driveshaft Center Support Bearing Bolts
M8 x 1.25
2
Driveshaft Center Support Bearing Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Secures the center support bearing on two-piece drive shafts. Estimated value; verify with specific service manual.
Differential
1 Differential Housing Mounting Bolts
M12 x 1.75
1
Differential Housing Mounting Bolts
M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Secures the differential housing to the chassis or subframe. Estimated value; verify with specific service manual.
2 Differential Drain/Fill Plug
M18 x 1.5
2
Differential Drain/Fill Plug
M18 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Proper torque prevents leaks from the drain and fill plugs. Use a new sealing washer if possible.
Axle
1 Drive Axle/Half Shaft Bolts
M10 x 1.25
1
Drive Axle/Half Shaft Bolts
M10 x 1.25
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Bolts that connect the drive axles to the transmission and wheel hubs. Always replace bolts, ensure a secure joint for power transfer.
2 CV Joint/Axle Nut
M22 x 1.5
2
CV Joint/Axle Nut
M22 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
Secures the CV joint and axle to the wheel hub. Use a new nut for proper torque.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Ignition System
1 Ignition Coil Mounting Bolt
M6 x 1.0
1
Ignition Coil Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Proper torque ensures good electrical ground for coil. Under-torquing can cause a poor connection, over-torquing can damage coil or threads.
Starting System
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secure mounting and ground path is critical. Improper torque can cause movement, bad ground, and starting issues.
Charging System
1 Alternator Mounting Bolts
M10 x 1.5
1
Alternator Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
A solid connection is necessary for a good ground path. Improper torque can lead to vibration, noise, and ground issues.
Battery Connections
1 Battery Terminal Nuts
M8 x 1.25
1
Battery Terminal Nuts
M8 x 1.25
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Proper torque ensures a good electrical connection. Too loose results in a bad connection, too tight can damage terminal or post.
Electronic Control Modules
1 Engine Control Module (ECM) Mounting Bolts
M6 x 1.0
1
Engine Control Module (ECM) Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Proper torque ensures a secure connection for electrical grounding. Estimated value, verify with service manual.
2 Body Control Module (BCM) Mounting Bolts
M6 x 1.0
2
Body Control Module (BCM) Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Proper torque ensures a secure electrical ground. Estimated value, verify with service manual.
Power Distribution
1 Fuse Box Mounting Bolts
M6 x 1.0
1
Fuse Box Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Securely mounting the fuse box is important for the integrity of electrical connections. Estimated value, verify with service manual.
2 Ground Strap Bolts/Screws
M6 x 1.0
2
Ground Strap Bolts/Screws
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Proper torque is essential to ensure low resistance and prevent corrosion. Estimated value, verify with service manual.
Sensor Mounting
1 Crankshaft Position Sensor Mounting Bolt
M6 x 1.0
1
Crankshaft Position Sensor Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Proper torque ensures proper positioning and a reliable ground. Estimated value, verify with service manual.
2 Camshaft Position Sensor Mounting Bolt
M6 x 1.0
2
Camshaft Position Sensor Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Proper torque ensures proper positioning and a reliable ground. Estimated value, verify with service manual.
3 Vehicle Speed Sensor Mounting Bolt
M6 x 1.0
3
Vehicle Speed Sensor Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Proper torque ensures proper positioning and a reliable ground. Estimated value, verify with service manual.
Lighting System
1 Headlight/Taillight Mounting Screws/Bolts
M5 x 0.8
1
Headlight/Taillight Mounting Screws/Bolts
M5 x 0.8
Torque Specification
4.3 ft-lbs (6 N·m)
Important Notes
Secure fastening is important, do not overtighten. Estimated value, verify with service manual.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Egr System
1 EGR Valve Mounting Bolts
M8 x 1.25
1
EGR Valve Mounting Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure mating surfaces are clean and use a new gasket. Tighten bolts in a crisscross pattern to ensure even clamping pressure.
Exhaust Manifold
1 Exhaust Manifold to Cylinder Head Bolts
M10 x 1.5
1
Exhaust Manifold to Cylinder Head Bolts
M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use a new exhaust manifold gasket. Tighten bolts in a specified sequence, starting from the center and working outwards to ensure even clamping pressure.
2 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.5
2
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use new gaskets and ensure proper alignment. Ensure the bolts are tightened evenly to maintain a leak-free seal.
3 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
3
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new gasket, if applicable. Ensure proper alignment of the catalytic converter and pipe. Bolts should be tightened evenly.
4 Muffler to Exhaust Pipe Bolts
M10 x 1.5
4
Muffler to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use new gaskets and ensure proper alignment. Tighten evenly to prevent exhaust leaks.
Oxygen Sensors
1 Oxygen (O2) Sensor (Threaded)
M18 x 1.5
1
Oxygen (O2) Sensor (Threaded)
M18 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
If the sensor has a crush washer, this torque spec should be adequate to compress the washer. Always double check the torque for the specific sensor. This is an estimated value.
Nox Sensors
1 NOx Sensor Mounting Bolts/Nuts
M6 x 1.0
1
NOx Sensor Mounting Bolts/Nuts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure a good seal with proper mounting. Do not over-tighten, as the sensors are sensitive and the bolts are small. Estimated value; confirm specific torque for your sensor.
Maf Sensor
1 Mass Air Flow (MAF) Sensor Mounting Bolts/Screws
M5 x 0.8
1
Mass Air Flow (MAF) Sensor Mounting Bolts/Screws
M5 x 0.8
Torque Specification
0.7 ft-lbs (1 N·m)
Important Notes
Tighten carefully to prevent damage to the sensor housing. This is an estimated value. These are very low torque values.
Egt Sensors
1 Exhaust Gas Temperature (EGT) Sensor Mounting Bolts/Nuts
M8 x 1.25
1
Exhaust Gas Temperature (EGT) Sensor Mounting Bolts/Nuts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the mating surfaces are clean and use anti-seize, if desired. Confirm the exact torque for your specific sensor. This is an estimated value.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold
1 Exhaust Manifold to Cylinder Head Bolts
M8 x 1.25
1
Exhaust Manifold to Cylinder Head Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten bolts in a criss-cross pattern starting from the center, to ensure even pressure on the gasket. Apply a thin coat of anti-seize to bolt threads if needed.
Exhaust Connecting Pipes
1 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.5
1
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten bolts in an alternating pattern to ensure even pressure on the gasket. Always use new gaskets for proper sealing.
2 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
2
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten bolts in an alternating pattern. Use new gaskets for proper sealing. Do not over-tighten.
3 Muffler to Exhaust Pipe Bolts
M10 x 1.5
3
Muffler to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten bolts evenly using an alternating pattern to ensure proper sealing and alignment. Replace gaskets when installing.
4 Exhaust Flange Bolts
M10 x 1.5
4
Exhaust Flange Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Tighten flange bolts in a criss-cross pattern. This value is an estimated average. Use a new gasket. For smaller bolts (M8), use 20 ft-lbs (27 N·m); for larger bolts (M12), use 37 ft-lbs (50 N·m).
Exhaust Hangers
1 Exhaust System Hanger Bolts
M8 x 1.25
1
Exhaust System Hanger Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the exhaust system with the hangers. Do not over-tighten to avoid damaging rubber isolators. This torque spec is an estimate and applies to most M8 hanger bolts.
Oxygen Sensors
1 Oxygen Sensor (O2 sensor) Threads
M18 x 1.5
1
Oxygen Sensor (O2 sensor) Threads
M18 x 1.5
Torque Specification
34 ft-lbs (46 N·m)
Important Notes
Apply a small amount of anti-seize to the threads of the oxygen sensor. This torque spec is an estimate and applies to most common O2 sensors. Avoid cross-threading the sensor. Do not overtighten.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Rail
1 Fuel Rail Mounting Bolts
M6 x 1.0
1
Fuel Rail Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent fuel rail distortion.
2 Fuel Injector Mounting Bolts
M5 x 0.8
2
Fuel Injector Mounting Bolts
M5 x 0.8
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts evenly to ensure proper injector seal.
Fuel Pump
1 Fuel Pump Mounting Bolts
M8 x 1.25
1
Fuel Pump Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper seating of the fuel pump before tightening.
2 Fuel Tank Sending Unit Lock Ring
N/A - Lock Ring
2
Fuel Tank Sending Unit Lock Ring
N/A - Lock Ring
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Ensure the lock ring is fully engaged. Torque may vary slightly based on lock ring style.
3 Fuel Tank Drain Plug
M12 x 1.75
3
Fuel Tank Drain Plug
M12 x 1.75
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the drain plug seal is in good condition before installing. Torque is estimated based on size.
4 Fuel Filler Neck Mounting Bolts
M8 x 1.25
4
Fuel Filler Neck Mounting Bolts
M8 x 1.25
Torque Specification
62 ft-lbs (84 N·m)
Important Notes
Tighten bolts in a star pattern to ensure even clamping.
Fuel Filter
1 Fuel Filter Mounting Bolt/Nut
M8 x 1.25
1
Fuel Filter Mounting Bolt/Nut
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Make sure the filter is aligned correctly before torquing the mounting hardware.
Fuel Evap
1 Vapor Canister Mounting Bolts
M6 x 1.0
1
Vapor Canister Mounting Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten bolts evenly to ensure proper grounding.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Ac Compressor
1 A/C Compressor Mounting Bolts
M10 x 1.5
1
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure bolts are clean and free of debris. Use a criss-cross pattern when tightening.
2 A/C Compressor Clutch Bolt
M8 x 1.25
2
A/C Compressor Clutch Bolt
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten to the specified range using a torque wrench. Use thread locker if necessary.
Ac Lines And Fittings
1 A/C Line Fittings
Varies, typical M8 x 1.25
1
A/C Line Fittings
Varies, typical M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure O-rings are properly seated and not damaged. Do not overtighten. Confirm specific size and manual specifications.
2 A/C Pressure Sensor
M10 x 1.0
2
A/C Pressure Sensor
M10 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Ensure O-ring is in place and not damaged. Torque carefully.
3 Expansion Valve Mounting Bolts/Screws
M6 x 1.0
3
Expansion Valve Mounting Bolts/Screws
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment and sealing of the expansion valve. Do not overtighten. Estimated value.
Ac Condenser
1 A/C Condenser Mounting Bolts/Nuts
M8 x 1.25
1
A/C Condenser Mounting Bolts/Nuts
M8 x 1.25
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten evenly. Confirm specific size with manual. Estimated value.
Ac Evaporator
1 A/C Evaporator Core Housing Bolts/Screws
M5 x 0.8
1
A/C Evaporator Core Housing Bolts/Screws
M5 x 0.8
Torque Specification
5.9 ft-lbs (8 N·m)
Important Notes
Do not overtighten. Use a precision torque wrench. Estimated value.
Hvac Actuators
1 HVAC Blend Door Actuator Mounting Screws/Bolts
M5 x 0.8
1
HVAC Blend Door Actuator Mounting Screws/Bolts
M5 x 0.8
Torque Specification
5.2 ft-lbs (7 N·m)
Important Notes
Tighten carefully to avoid damage to plastic components. Estimated value.
2 HVAC Mode Door Actuator Mounting Screws/Bolts
M5 x 0.8
2
HVAC Mode Door Actuator Mounting Screws/Bolts
M5 x 0.8
Torque Specification
5.2 ft-lbs (7 N·m)
Important Notes
Tighten carefully to avoid damage to plastic components. Estimated value.
Blower Motor
1 Blower Motor Mounting Screws/Bolts
M5 x 0.8
1
Blower Motor Mounting Screws/Bolts
M5 x 0.8
Torque Specification
4.4 ft-lbs (6 N·m)
Important Notes
Ensure the blower motor is properly seated before tightening. Estimated value.
Receiver Drier
1 Receiver Drier/Accumulator Mounting Bolts
M8 x 1.25
1
Receiver Drier/Accumulator Mounting Bolts
M8 x 1.25
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Ensure bolts are clean. Confirm specific size with manual. Estimated value.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Front Strut Assembly
1 Strut Mounting Bolts
M14 x 1.5
1
Strut Mounting Bolts
M14 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure proper alignment of the strut before tightening. Use a torque wrench for accurate values. Check torque after initial test drive.
Front Control Arms
1 Control Arm Mounting Bolts (Frame Side)
M14 x 1.5
1
Control Arm Mounting Bolts (Frame Side)
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Tighten with the suspension at normal ride height to avoid binding. Use a calibrated torque wrench.
2 Control Arm Ball Joint Nut
M12 x 1.25
2
Control Arm Ball Joint Nut
M12 x 1.25
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure ball joint is properly seated. Check for play after tightening. Some vehicles may have a castle nut and require a cotter pin.
3 Upper Control Arm Mounting Bolts
M12 x 1.5
3
Upper Control Arm Mounting Bolts
M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Tighten with the suspension at normal ride height. Double-check after test drive.
Steering System
1 Tie Rod End Nut
M10 x 1.25
1
Tie Rod End Nut
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the tie rod end. If equipped with a castle nut use cotter pin.
Sway Bar
1 Sway Bar Link Nut
M10 x 1.5
1
Sway Bar Link Nut
M10 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensure the sway bar link is seated correctly. Verify torque after a test drive.
2 Sway Bar Mounting Bracket Bolts
M8 x 1.25
2
Sway Bar Mounting Bracket Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the sway bar brackets are properly aligned and that the bushings are seated correctly.
Wheel Hub And Bearing
1 Wheel Hub/Bearing Mounting Bolts
M12 x 1.5
1
Wheel Hub/Bearing Mounting Bolts
M12 x 1.5
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Torque evenly and sequentially to ensure proper seating of the hub and bearing assembly. Double check torque after short test drive.
Rear Suspension
1 Trailing Arm Mounting Bolts
M14 x 1.5
1
Trailing Arm Mounting Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Tighten with the suspension at normal ride height. Double-check after the first test drive.
2 Rear Shock Absorber Mounting Bolts
M12 x 1.5
2
Rear Shock Absorber Mounting Bolts
M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure proper alignment of the shock. Use a torque wrench for accurate values.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What are the general torque specifications for the 2017-Present Cadillac XT5?
Q1
What are the general torque specifications for the 2017-Present Cadillac XT5?
Refer to the XT5 Service Manual for detailed specifications. As a general guideline, follow SAE J429 specifications for different bolt grades and sizes.
Q2 How do I ensure accurate torque application?
Q2
How do I ensure accurate torque application?
Use a properly calibrated torque wrench. Clean bolt threads and apply a light coat of thread lubricant to minimize friction and ensure proper torque transfer.
Q3 What are some common mistakes to avoid when tightening bolts?
Q3
What are some common mistakes to avoid when tightening bolts?
Avoid overtightening bolts, as it can damage threads or the component. Do not use impact wrenches for final tightening, as they may not provide consistent torque.
Q4 How do I determine the torque sequence for different components?
Q4
How do I determine the torque sequence for different components?
Refer to the XT5 Service Manual for precise torque sequences. Proper sequencing ensures even load distribution and prevents component damage.
Q5 What tools are required for proper torque application?
Q5
What tools are required for proper torque application?
A torque wrench with appropriate range and accuracy IS essential. Ensure the wrench IS calibrated regularly to maintain precision.
Q6 How often should torque be checked and re-applied?
Q6
How often should torque be checked and re-applied?
Inspect and re-torque critical bolts and fasteners as per scheduled maintenance intervals or as specified in the XT5 Service Manual. Regular torque checks ensure component integrity and safety.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the xt5.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Wheel Lug Nut Tightening Procedure
Properly tightening wheel lug nuts IS crucial for safe driving. This procedure provides detailed instructions for the xt5.
- Clean wheel lug nuts and threads
- Apply a thin film of anti-seize lubricant
- Hand-tighten lug nuts onto the wheel
- Use a torque wrench to tighten lug nuts to 140 Nm
- Follow a star pattern to ensure even tightening
- Recheck torque after 50 miles of driving
Engine Oil Drain Plug Tightening Procedure
Replacing engine oil requires proper tightening of the drain plug to prevent leaks. This procedure outlines the steps for the xt5.
- Clean drain plug and washer
- Apply a new washer to the drain plug
- Hand-tighten drain plug into the oil pan
- Use a torque wrench to tighten drain plug to 25 Nm
- Dispose of old oil and replace with new oil according to manufacturer's recommendations
Technical Service Bulletins
Front Brake Rotor Replacement Recommendations
2018-03-01This bulletin provides updated torque specifications for front brake rotor replacement on the xt5.
2017-2019 xt5
Resolution: When replacing front brake rotors on the affected vehicles, tighten the caliper mounting bolts to 120 Nm and the rotor retaining screws to 10 Nm.
Power Steering Fluid Leak Repair
2020-07-15This bulletin addresses a potential power steering fluid leak on the xt5. It includes instructions for diagnosing and repairing the leak.
2017-2021 xt5
Resolution: Inspect the power steering system for leaks. If a leak IS found, replace the faulty component (e.g., hose, seal). Tighten all bolts and fittings to 25 Nm.
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.