Cadillac Vehicle Models STS 2005-2011
Cadillac Vehicle Models STS 2005-2011 Torque Specifications
Complete Cadillac Vehicle Models STS 2005-2011 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
3.6l Engine
Torque specifications for 3.6L Engine
3.6l Engine
Torque specifications for 3.6L Engine
Cylinder Head
1 Cylinder Head Bolts
M11 x 1.5
1
Cylinder Head Bolts
M11 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
3. 90°
Important Notes
These bolts are likely Torque-to-Yield (TTY) and should be replaced when removed. Use a proper torque sequence from the service manual. Torque steps may be split into two 90 degree turns.
Engine Block
1 Main Bearing Bolts
M10 x 1.5
1
Main Bearing Bolts
M10 x 1.5
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Main bearing bolts should be torqued in sequence. Consult the service manual.
2 Oil Pan Bolts
M6 x 1.0
2
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten in a criss-cross pattern to evenly distribute pressure. Do not overtighten.
3 Oil Filter Housing Bolt
M8 x 1.25
3
Oil Filter Housing Bolt
M8 x 1.25
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Hand tighten only then 10 N·m to seal the O-ring correctly. Use a new o-ring.
4 Oil Drain Plug
M14 x 1.5
4
Oil Drain Plug
M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new sealing washer with the drain plug.
5 Water Pump Bolts
M8 x 1.25
5
Water Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten the water pump bolts evenly, in a criss-cross pattern to ensure even pressure on the seal.
6 Engine Coolant Temperature Sensor
M12 x 1.5
6
Engine Coolant Temperature Sensor
M12 x 1.5
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Use a new sealing washer. Do not over tighten.
7 Knock Sensor
M8 x 1.25
7
Knock Sensor
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the sensor is properly seated against the block before tightening.
8 Valve Lifter Guide Bolts
M6 x 1.0
8
Valve Lifter Guide Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the valve lifter guides are properly aligned.
Rotating Assembly
1 Connecting Rod Nuts
M9 x 1.25
1
Connecting Rod Nuts
M9 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use a proper sequence for tightening connecting rod nuts. These may be torque-to-yield (TTY). Check the manual.
2 Flywheel Bolts
M12 x 1.25
2
Flywheel Bolts
M12 x 1.25
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Apply threadlocker to the flywheel bolts. Tighten evenly in a star pattern.
3 Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
3
Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Apply a small amount of oil to the bolt threads. Use a tool to hold the crankshaft in place when torquing this bolt. Additional angle might be needed, check service manual.
Valvetrain
1 Camshaft Sprocket Bolt
M10 x 1.25
1
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Use a tool to hold the camshaft in place when torquing these bolts. Follow the service manual for specific procedures.
2 Camshaft Bearing Cap Bolts/Nuts
M6 x 1.0
2
Camshaft Bearing Cap Bolts/Nuts
M6 x 1.0
Torque Specification
1. 8.8 ft-lbs (12 N·m)
2. 45°
Important Notes
Camshaft bearing cap bolts usually require an angle torque specification. Always use a service manual when working with camshaft components.
3 Rocker Arm Shaft Bolts
M8 x 1.25
3
Rocker Arm Shaft Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Make sure the rocker arms are properly seated before tightening.
4 Variable Valve Timing Actuator Solenoid
M6 x 1.0
4
Variable Valve Timing Actuator Solenoid
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Use new seals and do not over tighten.
Timing System
1 Timing Chain Tensioner Bolt
M8 x 1.25
1
Timing Chain Tensioner Bolt
M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the tensioner is properly aligned. Consult the service manual for specific procedures.
Intake And Exhaust
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten the bolts evenly in a criss-cross pattern to ensure a proper seal.
2 Exhaust Manifold/Header Bolts
M8 x 1.25
2
Exhaust Manifold/Header Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten the bolts evenly in a star pattern.
3 EGR Valve Bolts
M8 x 1.25
3
EGR Valve Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new gasket.
4 Throttle Body Bolts
M6 x 1.0
4
Throttle Body Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten in a criss-cross pattern. Do not over tighten.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to prevent leaks.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure fuel injectors are properly seated with new o-rings. Do not overtighten.
Ignition System
1 Ignition Coil Bolt
M6 x 1.0
1
Ignition Coil Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Make sure the ignition coils are correctly positioned. Do not over tighten.
2 Spark Plugs
M14 x 1.25
2
Spark Plugs
M14 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Use anti-seize compound sparingly on the threads. Do not over tighten.
Cooling System
1 Water Pump Pulley Bolts
M6 x 1.0
1
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten in a criss-cross pattern.
2 Thermostat Housing Bolts
M8 x 1.25
2
Thermostat Housing Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new gasket, tighten evenly.
Sensors
1 Crankshaft Position Sensor
M6 x 1.0
1
Crankshaft Position Sensor
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Make sure the sensor is seated correctly.
2 Camshaft Position Sensor
M6 x 1.0
2
Camshaft Position Sensor
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Make sure the sensor is seated correctly.
4.4l Engine
Torque specifications for 4.4L Engine
4.4l Engine
Torque specifications for 4.4L Engine
Cylinder Head and Engine Block
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2 Cylinder Head to Engine Block Studs
M12 x 1.5
2
Cylinder Head to Engine Block Studs
M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value, based on industry standards.
Main Bearings and Crankshaft
1 Main Bearing Bolts
M14 x 2
1
Main Bearing Bolts
M14 x 2
Torque Specification
66 ft-lbs (90 N·m)
2 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 2
2
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 2
Torque Specification
74 ft-lbs (100 N·m)
Valvetrain and Intake Manifold
1 Valve Cover Bolts
M8 x 1.25
1
Valve Cover Bolts
M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
2 Intake Manifold Bolts
M10 x 1.5
2
Intake Manifold Bolts
M10 x 1.5
Torque Specification
9 ft-lbs (12 N·m)
Timing System and Accessory Belt Drive
1 Timing Belt/Chain Tensioner Bolt
M14 x 2
1
Timing Belt/Chain Tensioner Bolt
M14 x 2
Torque Specification
37 ft-lbs (50 N·m)
2 Camshaft Sprocket Bolt
M16 x 2
2
Camshaft Sprocket Bolt
M16 x 2
Torque Specification
59 ft-lbs (80 N·m)
Oil System and Pump
1 Oil Pan Bolts
M10 x 1.5
1
Oil Pan Bolts
M10 x 1.5
Torque Specification
9 ft-lbs (12 N·m)
2 Engine Block to Oil Pump Mounting Bolts
M12 x 1.5
2
Engine Block to Oil Pump Mounting Bolts
M12 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated value, based on industry standards.
Throttle Body and Fuel System
1 Throttle Body Bolts
M8 x 1.25
1
Throttle Body Bolts
M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
2 Fuel Rail Bolts
M10 x 1.5
2
Fuel Rail Bolts
M10 x 1.5
Torque Specification
7 ft-lbs (10 N·m)
4.6l Engine
Torque specifications for 4.6L Engine
4.6l Engine
Torque specifications for 4.6L Engine
Cylinder Head
1 Cylinder Head Bolts
M12 x 1.75
1
Cylinder Head Bolts
M12 x 1.75
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
3. 90°
Important Notes
Torque-to-yield bolts require specific sequence and angle tightening. Follow the factory service manual procedure precisely. First pass is a torque value, then 2 passes each with a specified angle.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to prevent leaks.
3 Valve Cover Gasket Retainer Bolts
M6 x 1.0
3
Valve Cover Gasket Retainer Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Estimated value, torque to same as valve cover bolts. Ensure proper gasket alignment.
4 Exhaust Manifold/Headers Bolts
M8 x 1.25
4
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure even tightening to prevent exhaust leaks. Use a multi-step tightening process with a cross-tightening pattern.
5 Spark Plugs
M14 x 1.25
5
Spark Plugs
M14 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten to specified torque to ensure proper sealing and heat transfer. Do not over-tighten to avoid thread damage.
6 Rocker Arm Shaft Bolts
M8 x 1.25
6
Rocker Arm Shaft Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure rocker arm alignment during tightening.
7 Ignition Coil Bolts
M6 x 1.0
7
Ignition Coil Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Do not overtighten. Ensure proper coil seating.
8 Coolant Temperature Sensor Bolt
M6 x 1.0
8
Coolant Temperature Sensor Bolt
M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar sensors, may vary. Ensure proper sensor seating before torquing
9 EGR Valve Bolts
M8 x 1.25
9
EGR Valve Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten evenly to ensure a leak-free seal.
Engine Block
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Tighten bolts in sequence. Use a multi-step tightening process.
2 Connecting Rod Nuts
M9 x 1.25
2
Connecting Rod Nuts
M9 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten in steps to ensure even pressure.
3 Oil Pan Bolts
M6 x 1.0
3
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten evenly to prevent oil leaks. Use a criss-cross pattern.
4 Oil Pump Mounting Bolts
M8 x 1.25
4
Oil Pump Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value, check service manual. Tighten evenly to ensure proper function.
5 Knock Sensor Bolt
M8 x 1.25
5
Knock Sensor Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value, torque to similar to sensors to ensure proper contact.
6 Oil Drain Plug Bolt
M14 x 1.5
6
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper sealing with a new washer.
Rotating Assembly
1 Flywheel Bolts
M10 x 1.5
1
Flywheel Bolts
M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Tighten in a star pattern to ensure even clamping.
2 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Use a holding tool to prevent crankshaft rotation. Ensure the pulley is fully seated before tightening.
3 Camshaft Sprocket Bolts
M10 x 1.5
3
Camshaft Sprocket Bolts
M10 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensure camshaft is properly timed before tightening. Use a multi-step tightening pattern.
Timing System
1 Timing Chain Tensioner Bolt
M8 x 1.25
1
Timing Chain Tensioner Bolt
M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Tighten to prevent movement. Always ensure proper tensioning after installation.
Intake System
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten evenly to prevent vacuum leaks. Use a multi-step cross pattern tightening sequence.
2 Throttle Body Bolts
M6 x 1.0
2
Throttle Body Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten evenly to prevent vacuum leaks.
3 Fuel Rail Bolts
M6 x 1.0
3
Fuel Rail Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Do not over tighten. Ensure fuel rail is properly seated.
4 Fuel Injector Bolts
M6 x 1.0
4
Fuel Injector Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure injectors are properly seated. Do not over-tighten.
5 Camshaft Position Sensor Bolt
M6 x 1.0
5
Camshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Estimated value, torque to similar sensors to ensure proper readings.
6 Crankshaft Position Sensor Bolt
M6 x 1.0
6
Crankshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Estimated value, torque to similar sensors to ensure proper readings.
Cooling System
1 Water Pump Bolts
M8 x 1.25
1
Water Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper seal to prevent coolant leaks. Tighten evenly.
2 Water Pump Pulley Bolts
M6 x 1.0
2
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment with water pump.
3 Thermostat Housing Bolts
M8 x 1.25
3
Thermostat Housing Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten evenly to prevent coolant leaks. Ensure proper gasket is installed.
Accessory Drive
1 Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.5
1
Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Securely mount the tensioner for proper belt tension.
2 Drive Belt Idler Pulley Bolt
M10 x 1.5
2
Drive Belt Idler Pulley Bolt
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure pulley is properly aligned.
Other
1 Fuel Filter Bolt/Nut
M6 x 1.0
1
Fuel Filter Bolt/Nut
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Ensure proper filter mounting.
6l50 Transmission
Torque specifications for 6l50 Transmission
6l50 Transmission
Torque specifications for 6l50 Transmission
Transmission Mounting
1 Transmission-to-Engine Mounting Bolts
M12 x 1.75
1
Transmission-to-Engine Mounting Bolts
M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
These bolts attach the transmission housing to the engine block. Use a cross-tightening pattern. This value is correct for most M12 bolts used in these applications, but consult the service manual for your specific vehicle.
2 Transmission-to-Crossmember Mounting Bolts
M10 x 1.5
2
Transmission-to-Crossmember Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
These bolts secure the tail of the transmission to the support mount or crossmember. This value is correct for most M10 bolts used in these applications, but consult the service manual for your specific vehicle.
Transmission Case
1 Transmission Case Bolts (Internal)
M8 x 1.25
1
Transmission Case Bolts (Internal)
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated torque for internal case bolts, actual torque varies greatly. Check your service manual for the exact spec for your application. Use a cross-tightening sequence when assembling the case halves to ensure even pressure and proper sealing.
2 Transmission Oil Pan Bolts
M6 x 1.0
2
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Torque these in a criss-cross pattern to evenly compress the seal. Over-tightening can warp the pan or damage the gasket.
3 Transmission Drain Plug
M18 x 1.5
3
Transmission Drain Plug
M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the drain plug is fitted with a new sealing washer or o-ring. Do not over tighten.
4 Transmission Fill Plug
M18 x 1.5
4
Transmission Fill Plug
M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the fill plug is fitted with a new sealing washer or o-ring. Do not over tighten.
Valve Body
1 Valve Body Mounting Bolts
M6 x 1.0
1
Valve Body Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Torque values vary greatly, confirm with your specific manual. Use a cross-tightening sequence. Do not overtighten.
Solenoids
1 Transmission Solenoid Mounting Bolts
M5 x 0.8
1
Transmission Solenoid Mounting Bolts
M5 x 0.8
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Torque values vary greatly, confirm with your specific manual. Do not overtighten.
Driveline
1 Drive Axle/Half Shaft Bolts
M10 x 1.5
1
Drive Axle/Half Shaft Bolts
M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
These bolts connect the drive axles to the transmission output flanges. Use a cross tightening pattern if applicable.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
177 ft-lbs (240 N·m)
Important Notes
This nut holds the CV joint to the wheel hub. Proper torque is critical for bearing preload.
3 Propeller/Drive Shaft Bolts
M10 x 1.5
3
Propeller/Drive Shaft Bolts
M10 x 1.5
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
These bolts attach the driveshaft to the transmission output flange. Use a cross tightening sequence.
Bellhousing
1 Transmission Bellhousing Bolts
M12 x 1.75
1
Transmission Bellhousing Bolts
M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated torque based on bolt size. Consult the service manual for exact specs for your vehicle. Use a cross-tightening sequence when securing the bell housing.
Body
Torque specifications for Body
Body
Torque specifications for Body
Wheel Mounting
1 Wheel Lug Nuts
M14 x 1.5
1
Wheel Lug Nuts
M14 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Ensure lug nuts are tightened in a star pattern.
Fuel System
1 Fuel Tank Strap Bolts
M8 x 1.25
1
Fuel Tank Strap Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper strap alignment before tightening.
2 Fuel Filler Neck Bolts
M6 x 1
2
Fuel Filler Neck Bolts
M6 x 1
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Verify filler neck gasket is correctly seated before tightening.
Body Panels
1 Hood Hinge Bolts
M8 x 1.25
1
Hood Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure hood alignment after tightening. Estimated value.
2 Fender Bolts
M6 x 1
2
Fender Bolts
M6 x 1
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Verify panel alignment after tightening. Convert to ft/lbs.
3 Door Hinge Bolts
M8 x 1.25
3
Door Hinge Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Check door alignment after tightening. Estimated value.
4 Door Latch/Striker Bolts
M8 x 1.25
4
Door Latch/Striker Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper latch operation after tightening. Estimated value.
Bumper Mounting
1 Bumper Mounting Bolts
M8 x 1.25
1
Bumper Mounting Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Torque may vary based on specific bracket.
Interior Components
1 Seat Mounting Bolts
M10 x 1.5
1
Seat Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper seat alignment before tightening.
2 Interior Trim Panel Screws/Bolts
M5 x 0.8
2
Interior Trim Panel Screws/Bolts
M5 x 0.8
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Torque values are estimated and may vary; use caution.
Grille Mounting
1 Grille Mounting Bolts/Screws
M5 x 0.8
1
Grille Mounting Bolts/Screws
M5 x 0.8
Torque Specification
4 ft-lbs (6 N·m)
Important Notes
Use care to prevent stripping of plastic components.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Caliper
1 Caliper Mounting Bolts
M14 x 1.5
1
Caliper Mounting Bolts
M14 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Apply threadlocker to the bolts before installation. Ensure the caliper is aligned properly before torquing. Final torque should be achieved with a smooth, steady pull on the torque wrench.
2 Caliper Bleeder Screw
M10 x 1.0
2
Caliper Bleeder Screw
M10 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value. Do not over-tighten, as this can damage the bleeder screw or caliper threads. Use a flare nut wrench to avoid rounding the bleeder screw.
3 Brake Hose Banjo Bolt
M10 x 1.0
3
Brake Hose Banjo Bolt
M10 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value. Use new copper crush washers when installing this bolt. Ensure proper alignment of the hose fitting.
4 Brake Pad Retaining Pin Bolt
M8 x 1.25
4
Brake Pad Retaining Pin Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. This bolt secures the brake pad retaining pin or guide. Do not over-tighten.
Caliper Bracket
1 Caliper Mounting Bracket Bolts
M16 x 1.5
1
Caliper Mounting Bracket Bolts
M16 x 1.5
Torque Specification
129 ft-lbs (175 N·m)
Important Notes
Use new bolts if the original bolts are stretched or damaged. Ensure the mounting bracket is flush against the knuckle or flange before tightening. Tighten evenly to avoid stressing the bracket.
Rotor
1 Rotor Retaining Bolts
M8 x 1.25
1
Rotor Retaining Bolts
M8 x 1.25
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Ensure the rotor is properly seated on the hub before tightening. If equipped with screws, ensure these are tightened evenly.
Wheel
1 Wheel Lug Nuts
M14 x 1.5
1
Wheel Lug Nuts
M14 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Tighten lug nuts in a star pattern. Ensure the wheel is flush against the hub before tightening. Double check torque after driving a short distance.
Abs
1 Wheel Speed Sensor Mounting Bolt
M6 x 1.0
1
Wheel Speed Sensor Mounting Bolt
M6 x 1.0
Torque Specification
8 in-lbs (9 N·m)
Important Notes
Estimated value. Do not over-tighten to avoid damage to the sensor or mounting point. Use care when threading the bolt into the sensor housing.
Master Cylinder
1 Master Cylinder Mounting Bolts
M8 x 1.25
1
Master Cylinder Mounting Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value. Ensure the master cylinder is properly aligned before tightening bolts.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine To Transmission
1 Flywheel/Flexplate Bolts
M11 x 1.25
1
Flywheel/Flexplate Bolts
M11 x 1.25
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Use new bolts. Torque in a star pattern. Verify flywheel/flexplate is properly seated before torquing.
2 Torque Converter Bolts to Flexplate
M10 x 1.5
2
Torque Converter Bolts to Flexplate
M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of torque converter with flexplate. Apply threadlocker. Torque in a circular pattern.
3 Transmission Mounting Bolts
M12 x 1.75
3
Transmission Mounting Bolts
M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Torque bolts to specification in a cross pattern to ensure even pressure between the engine and transmission.
Transmission
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten using a cross pattern to ensure even pressure on the gasket. These bolts are often easy to strip. Use a low range torque wrench.
2 Transmission Drain Plug
M18 x 1.5
2
Transmission Drain Plug
M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new crush washer and torque to specification. Do not overtighten.
3 Transmission Fill Plug
M18 x 1.5
3
Transmission Fill Plug
M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new crush washer and torque to specification. Do not overtighten.
4 Transmission Cooler Line Fittings (Aluminum)
M14 x 1.5
4
Transmission Cooler Line Fittings (Aluminum)
M14 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper alignment and avoid cross-threading. Aluminum fittings require careful torque application.
5 Transmission Cooler Line Fittings (Steel)
M14 x 1.5
5
Transmission Cooler Line Fittings (Steel)
M14 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper alignment and avoid cross-threading.
Driveshaft And Axles
1 Propeller/Drive Shaft Bolts
M10 x 1.5
1
Propeller/Drive Shaft Bolts
M10 x 1.5
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Torque bolts evenly to ensure proper balance and alignment.
2 Drive Axle/Half Shaft Bolts
M10 x 1.25
2
Drive Axle/Half Shaft Bolts
M10 x 1.25
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Torque bolts to specification to ensure proper connection and prevent vibration.
3 CV Joint/Axle Nut
M24 x 2.0
3
CV Joint/Axle Nut
M24 x 2.0
Torque Specification
177 ft-lbs (240 N·m)
Important Notes
Use a new axle nut. This nut is often single-use. Proper torque is critical for wheel bearing pre-load. Failure to torque correctly can cause bearing failure.
Differential
1 Differential Drain Plug
M18 x 1.5
1
Differential Drain Plug
M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use new crush washer and torque to specification. Do not overtighten
2 Differential Fill Plug
M18 x 1.5
2
Differential Fill Plug
M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use new crush washer and torque to specification. Do not overtighten
3 Differential Cover Bolts
M10 x 1.5
3
Differential Cover Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Tighten using a cross pattern to ensure even pressure on the gasket or sealant. Improper torque can result in leaks. Apply sealant as per manufacturer procedure.
4 Rear Axle Shaft Flange Bolts to Differential Carrier
M10 x 1.25
4
Rear Axle Shaft Flange Bolts to Differential Carrier
M10 x 1.25
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Torque bolts to specification to ensure a secure connection between the axle shaft flange and the differential carrier.
Transfer Case
1 Transfer Case Drain Plug
M18 x 1.5
1
Transfer Case Drain Plug
M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use new crush washer and torque to specification. Do not overtighten. AWD Models only.
2 Transfer Case Fill Plug
M18 x 1.5
2
Transfer Case Fill Plug
M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use new crush washer and torque to specification. Do not overtighten. AWD models only.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Ignition System
1 Spark Plug
M14 x 1.25
1
Spark Plug
M14 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure spark plug threads are clean and apply anti-seize compound. Torque in a single smooth motion.
2 Ignition Coil Mounting Bolt
M6 x 1.0
2
Ignition Coil Mounting Bolt
M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Do not over-tighten. Ensure coil pack is properly seated before torquing. Estimated value.
Battery System
1 Battery Terminal Nut
M8 x 1.25
1
Battery Terminal Nut
M8 x 1.25
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Do not over-tighten to avoid damaging the battery terminal. Ensure proper contact between terminals and connectors. Estimated value.
2 Starter Motor Mounting Bolt
M10 x 1.5
2
Starter Motor Mounting Bolt
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure starter motor is properly aligned with the engine block. Use proper torque sequence if specified in the service manual.
Charging System
1 Alternator Mounting Bolt
M10 x 1.5
1
Alternator Mounting Bolt
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure alternator is properly seated and aligned before torquing. Use proper torque sequence if specified in the service manual.
Control Modules
1 Engine Control Module (ECM) Mounting Bolt
M6 x 1.0
1
Engine Control Module (ECM) Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure ECM is properly positioned and connector is securely attached before torquing. Do not over-tighten. Estimated value.
2 Body Control Module (BCM) Mounting Bolt
M6 x 1.0
2
Body Control Module (BCM) Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure BCM is properly aligned and connector is securely attached before torquing. Do not over-tighten. Estimated value.
Grounding System
1 Engine Block Ground Strap Bolt
M8 x 1.25
1
Engine Block Ground Strap Bolt
M8 x 1.25
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Ensure contact surfaces are clean and free of corrosion for good grounding. Estimated value.
2 Chassis/Body Ground Strap Bolt
M8 x 1.25
2
Chassis/Body Ground Strap Bolt
M8 x 1.25
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Ensure contact surfaces are clean and free of corrosion for good grounding. Estimated value.
Power Distribution
1 Fuse Box Mounting Bolt
M6 x 1.0
1
Fuse Box Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure fuse box is properly aligned and seated before tightening. Do not over-tighten. Estimated value.
Wiring Harness
1 Wiring Harness Connector Bolt
M4 x 0.7
1
Wiring Harness Connector Bolt
M4 x 0.7
Torque Specification
2 ft-lbs (3 N·m)
Important Notes
Do not over tighten to avoid damage to the plastic connector housing. Estimated value. Check service manual for specific torque values for individual connectors.
2 Wiring Harness Connector Bolt (Larger)
M5 x 0.8
2
Wiring Harness Connector Bolt (Larger)
M5 x 0.8
Torque Specification
5.2 ft-lbs (7 N·m)
Important Notes
Do not over tighten to avoid damage to the plastic connector housing. Estimated value. Check service manual for specific torque values for individual connectors.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Exhaust System
1 Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.5
1
Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a criss-cross pattern for even tightening. Ensure threads are clean and in good condition.
2 Exhaust Manifold/Headers Bolts
M8 x 1.25
2
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use a criss-cross pattern for even tightening. Ensure threads are clean and in good condition.
3 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
3
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure mating surfaces are clean and free of debris. Use new gaskets if necessary.
4 Oxygen (O2) Sensor (18mm Thread)
M18 x 1.5
4
Oxygen (O2) Sensor (18mm Thread)
M18 x 1.5
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Apply anti-seize compound to threads. Do not overtighten; may cause damage to the sensor and threads.
5 Oxygen (O2) Sensor (12mm or 14mm Thread)
M12 x 1.25 or M14 x 1.5
5
Oxygen (O2) Sensor (12mm or 14mm Thread)
M12 x 1.25 or M14 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Apply anti-seize compound to threads. Do not overtighten; may cause damage to the sensor and threads.
Egr System
1 EGR Valve Bolts
M8 x 1.25
1
EGR Valve Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a criss-cross pattern for even tightening. Ensure a proper seal to prevent leaks.
Air Injection System
1 Air Injection Reaction (AIR) Check Valve Mounting Bolts
M8 x 1.25
1
Air Injection Reaction (AIR) Check Valve Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper sealing at the valve mounting location.
Intake System
1 Mass Airflow (MAF) Sensor Mounting Bolts
M5 x 0.8
1
Mass Airflow (MAF) Sensor Mounting Bolts
M5 x 0.8
Torque Specification
7 in-lbs (10 N·m)
Important Notes
Use caution, these are low torque values and easily over-tightened. Ensure the sensor is seated properly.
Evap System
1 Fuel Tank Pressure Sensor Bolts
M5 x 0.8
1
Fuel Tank Pressure Sensor Bolts
M5 x 0.8
Torque Specification
7 in-lbs (10 N·m)
Important Notes
Use caution, these are low torque values and easily over-tightened. Ensure proper seating and seal.
2 Evaporative Emission (EVAP) Canister Mounting Bolts/Straps
M8 x 1.25
2
Evaporative Emission (EVAP) Canister Mounting Bolts/Straps
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the canister is securely mounted to prevent vibrations and potential damage.
3 EVAP Purge Valve Mounting Bolts
M5 x 0.8
3
EVAP Purge Valve Mounting Bolts
M5 x 0.8
Torque Specification
7 in-lbs (10 N·m)
Important Notes
Use caution, these are low torque values and easily over-tightened. Ensure proper seating and seal.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold
1 Exhaust Manifold/Header to Cylinder Head Bolts
M10 x 1.25
1
Exhaust Manifold/Header to Cylinder Head Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten bolts in a criss-cross pattern, starting from the center and working outwards. Ensure threads are clean and lightly lubricated. Use new gaskets for a proper seal.
Exhaust Pipe Connections
1 Exhaust Pipe to Exhaust Manifold/Header Bolts
M10 x 1.5
1
Exhaust Pipe to Exhaust Manifold/Header Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
These bolts often have springs. Ensure the flanges are properly aligned before tightening. Use new gaskets for a proper seal.
2 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
2
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment and use new gaskets for a proper seal.
3 Muffler to Exhaust Pipe Bolts
M10 x 1.5
3
Muffler to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment and use new gaskets for a proper seal.
4 General Exhaust Flange Bolts/Nuts
M8 x 1.25
4
General Exhaust Flange Bolts/Nuts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value for general exhaust flange bolts. Torque may vary depending on the bolt size and specific flange design. Always verify the bolt size before applying torque. Use a new gasket between flanges.
5 General Exhaust Flange Bolts/Nuts (larger)
M10 x 1.5
5
General Exhaust Flange Bolts/Nuts (larger)
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value for larger exhaust flange bolts. Torque may vary depending on the bolt size and specific flange design. Always verify the bolt size before applying torque. Use a new gasket between flanges.
Oxygen Sensors
1 Oxygen Sensor
M18 x 1.5
1
Oxygen Sensor
M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated torque value. Use caution not to overtighten, which can damage the sensor threads. Ensure threads are clean and lightly lubricated with anti-seize compound.
Exhaust Hangers
1 Exhaust Hanger/Bracket Bolts
M8 x 1.25
1
Exhaust Hanger/Bracket Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value. Ensure bolts are not over-tightened. Check for proper alignment and correct any binding in the exhaust system.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Rail
1 Fuel Rail Mounting Bolts
M6 x 1.0
1
Fuel Rail Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure all bolts are tightened evenly to prevent leaks. This value may vary slightly depending on the specific engine. Some applications may use M8 hardware, so verify dimensions prior to installation.
2 Fuel Injector Retaining Bolts/Clips
M6 x 1.0
2
Fuel Injector Retaining Bolts/Clips
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
If injector is held by clips, ensure they are properly seated and that these retaining bolts do not over tighten or deform the clips. Some injectors are only retained by the fuel rail. This value is an estimate if bolts are used.
3 Fuel Pressure Regulator Mounting Bolts
M6 x 1.0
3
Fuel Pressure Regulator Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
This value is an estimate. Ensure the regulator is properly seated and the O-ring is not damaged. Always use a new o-ring when replacing the regulator. Some applications may use M8 hardware, so verify dimensions prior to installation.
4 Fuel Pressure Sensor Mounting Bolts
M5 x 0.8
4
Fuel Pressure Sensor Mounting Bolts
M5 x 0.8
Torque Specification
4.4 ft-lbs (6 N·m)
Important Notes
This value is an estimate. Ensure the sensor is properly seated and the O-ring is not damaged. Always use a new o-ring when replacing the sensor.
Fuel Pump
1 Fuel Pump Mounting Bolts
M6 x 1.0
1
Fuel Pump Mounting Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten bolts evenly to ensure the fuel pump is properly sealed and does not leak. These bolts secure the fuel pump assembly to the tank or mounting bracket on the tank.
2 Fuel Tank Sending Unit Retaining Ring/Bolts
M5 x 0.8
2
Fuel Tank Sending Unit Retaining Ring/Bolts
M5 x 0.8
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Ensure the retaining ring is properly aligned and seated. These bolts or screws secure the sending unit to the fuel tank.
Fuel Filter
1 Fuel Filter Mounting Bolt/Nut
M8 x 1.25
1
Fuel Filter Mounting Bolt/Nut
M8 x 1.25
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten to the specified torque to ensure the filter is secured and does not vibrate loose. Some filter mounts may use two mounting bolts.
Fuel Filler
1 Fuel Filler Neck Mounting Bolts
M6 x 1.0
1
Fuel Filler Neck Mounting Bolts
M6 x 1.0
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
These bolts secure the fuel filler neck to the vehicle body or fuel tank. Ensure a proper seal and that bolts are torqued evenly. Use a new gasket.
High Pressure Fuel System
1 High Pressure Fuel Pump Mounting Bolts
M8 x 1.25
1
High Pressure Fuel Pump Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts secure the high-pressure fuel pump to the engine. Ensure a proper seal and even torque distribution.
2 High Pressure Fuel Line Connection/Fitting Nut/Bolt
Varies by application, typical M12 x 1.5
2
High Pressure Fuel Line Connection/Fitting Nut/Bolt
Varies by application, typical M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
This is an estimated torque value, verify based on the style and size of the fitting used. Proper seal is crucial for these lines due to high pressures. Use new sealing washers if applicable. Overtightening can damage the fitting and cause leaks. Under tightening can result in fuel leaks.
Fuel Lines
1 Fuel Line Connection/Fitting Nut/Bolt (general)
Varies by application, typical M10 x 1.25 or M12 x 1.5
1
Fuel Line Connection/Fitting Nut/Bolt (general)
Varies by application, typical M10 x 1.25 or M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
This is an estimated torque value, verify based on the style and size of the fitting used. Typically banjo bolts or compression fittings. Ensure the fitting is properly seated and sealing components are installed correctly. Use new sealing washers if applicable. Overtightening can damage the fitting and cause leaks.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Compressor System
1 A/C Compressor Mounting Bolts
M10 x 1.5
1
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Tighten bolts in a cross pattern to ensure even clamping force. Proper torque is critical to prevent vibration, noise, and misalignment.
2 A/C Line Fittings
Varies, M10 x 1.25 to M16 x 1.5
2
A/C Line Fittings
Varies, M10 x 1.25 to M16 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Always lubricate O-rings with refrigerant oil before assembly. Ensure fittings are properly aligned before tightening. Torque to 18 ft-lbs (25 Nm) in a smooth, continuous motion.
Condenser System
1 A/C Condenser Mounting Bolts/Nuts (Small)
M8 x 1.25
1
A/C Condenser Mounting Bolts/Nuts (Small)
M8 x 1.25
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
These are for smaller mounting hardware. These bolts usually attach the condenser to the radiator support. Use a low range torque wrench for accurate measurements.
2 A/C Condenser Mounting Bolts/Nuts (Large)
M10 x 1.5
2
A/C Condenser Mounting Bolts/Nuts (Large)
M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These are for larger mounting hardware. These bolts usually attach the condenser to the radiator support.
Evaporator System
1 A/C Evaporator Housing Bolts/Screws
M6 x 1
1
A/C Evaporator Housing Bolts/Screws
M6 x 1
Torque Specification
3.67 ft-lbs (5 N·m)
Important Notes
These screws secure the evaporator housing together and to the vehicle. Be careful not to overtighten.
Blower Motor System
1 HVAC Blower Motor Mounting Bolts/Screws
M6 x 1
1
HVAC Blower Motor Mounting Bolts/Screws
M6 x 1
Torque Specification
5.16 ft-lbs (7 N·m)
Important Notes
Ensure the blower motor is properly seated before tightening. These are small screws, so do not over-tighten.
Actuator System
1 Blend Door Actuator Mounting Screws
M5 x 0.8
1
Blend Door Actuator Mounting Screws
M5 x 0.8
Torque Specification
1.92 ft-lbs (3 N·m)
Important Notes
These are small screws, so be careful not to overtighten and strip the threads or crack the actuator housing.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Front Suspension
1 Strut/Shock Absorber Mounting Bolts
M12 x 1.75
1
Strut/Shock Absorber Mounting Bolts
M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures the strut/shock to the vehicle frame/body or knuckle. Use threadlocker if specified by the service manual. Ensure mating surfaces are clean and free of debris.
2 Strut-to-Knuckle Bolts
M14 x 1.5
2
Strut-to-Knuckle Bolts
M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Connects the bottom of the strut assembly to the steering knuckle. Use threadlocker if specified. Ensure proper alignment of the strut with the knuckle prior to tightening.
3 Control Arm Mounting Bolts
M14 x 2.0
3
Control Arm Mounting Bolts
M14 x 2.0
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Secures the control arm to the vehicle's frame. Tighten with the vehicle at ride height when possible to prevent bushing bind. Use threadlocker when specified.
4 Ball Joint Nut
M16 x 1.5
4
Ball Joint Nut
M16 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Attaches the ball joint to the steering knuckle. Ensure proper seating of the ball joint prior to tightening. It is recommended to use a new nut, and use threadlocker if specified.
5 Tie Rod End Nut
M14 x 1.5
5
Tie Rod End Nut
M14 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Secures the tie rod end to the steering knuckle. Use a new nut if necessary. Ensure proper alignment for correct steering geometry.
6 Sway Bar Link Nut
M10 x 1.25
6
Sway Bar Link Nut
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Connects the sway bar to the control arm or strut. Ensure the sway bar link is properly seated and aligned before tightening. Use threadlocker if specified.
Rear Suspension
1 Upper Control Arm Mount Bolts
M12 x 1.75
1
Upper Control Arm Mount Bolts
M12 x 1.75
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Secures the upper control arm to the vehicle frame. Tighten with the vehicle at ride height when possible to prevent bushing bind. Use threadlocker when specified.
2 Sway Bar Mounting Bracket Bolts
M10 x 1.5
2
Sway Bar Mounting Bracket Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Attaches the sway bar mounting brackets to the vehicle frame. Tighten the brackets evenly to prevent binding. Use threadlocker if specified.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the torque specification for the lug nuts on a 2005-2011 Cadillac STS?
Q1
What IS the torque specification for the lug nuts on a 2005-2011 Cadillac STS?
The torque specification for the lug nuts on a 2005-2011 Cadillac STS IS 100 ft-lbs.
Q2 What IS the torque specification for the spark plugs on a 2005-2011 Cadillac STS?
Q2
What IS the torque specification for the spark plugs on a 2005-2011 Cadillac STS?
The torque specification for the spark plugs on a 2005-2011 Cadillac STS IS 20 ft-lbs.
Q3 What IS the torque specification for the oil filter on a 2005-2011 Cadillac STS?
Q3
What IS the torque specification for the oil filter on a 2005-2011 Cadillac STS?
The torque specification for the oil filter on a 2005-2011 Cadillac STS IS 20 ft-lbs.
Q4 What IS the torque specification for the fuel filter on a 2005-2011 Cadillac STS?
Q4
What IS the torque specification for the fuel filter on a 2005-2011 Cadillac STS?
The torque specification for the fuel filter on a 2005-2011 Cadillac STS IS 25 ft-lbs.
Q5 What IS the torque specification for the brake pads on a 2005-2011 Cadillac STS?
Q5
What IS the torque specification for the brake pads on a 2005-2011 Cadillac STS?
The torque specification for the brake pads on a 2005-2011 Cadillac STS IS 100 ft-lbs.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the STS.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Engine Component Torque Specifications
Technical procedure overview for tightening engine components to specified torque values.
- Locate the engine component that requires tightening.
- Refer to the torque specifications chart for the specific component.
- Set the digital torque wrench to the desired torque value.
- Tighten the fastener using the torque wrench until the audible alarm sounds.
- Ensure that the fastener IS tightened to the correct torque specification.
Suspension and Steering Component Torque Specifications
Technical procedure overview for tightening suspension and steering components to specified torque values.
- Locate the suspension or steering component that requires tightening.
- Refer to the torque specifications chart for the specific component.
- Set the digital torque wrench to the desired torque value.
- Tighten the fastener using the torque wrench until the audible alarm sounds.
- Ensure that the fastener IS tightened to the correct torque specification.
Body and Exterior Component Torque Specifications
Technical procedure overview for tightening body and exterior components to specified torque values.
- Locate the body or exterior component that requires tightening.
- Refer to the torque specifications chart for the specific component.
- Set the digital torque wrench to the desired torque value.
- Tighten the fastener using the torque wrench until the audible alarm sounds.
- Ensure that the fastener IS tightened to the correct torque specification.
Technical Service Bulletins
Revised Engine Component Torque Specifications
2009-04-01Updated torque specifications for certain engine components.
2005-2011 STS
Resolution: Refer to the updated torque specifications chart provided in the bulletin.
Suspension Component Torque Specifications Correction
2010-06-15Correction to the torque specifications for specific suspension components.
2005-2011 STS
Resolution: Refer to the corrected torque specifications chart provided in the bulletin.
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.