Cadillac Vehicle Models Escalade 2002-2006 Torque Specifications
Cadillac Vehicle Models Escalade 2002-2006

Cadillac Vehicle Models Escalade 2002-2006 Torque Specifications

Complete Cadillac Vehicle Models Escalade 2002-2006 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

4l60 Transmission

Torque specifications for 4l60 Transmission

Transmission Mounting

1

Transmission Crossmember Mounting Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
These are typically M12-1.75 bolts with an 18mm socket head.

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8.83 ft-lbs (12 N·m)
Important Notes
These are typically M6 or M8 bolts. Always use a crisscross pattern when tightening.

Transmission Drain Fill Plugs

1

Transmission Drain Plug

M18 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Typically uses an o-ring seal.
2

Transmission Fill Plug

M18 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Typically uses an o-ring seal.

Torque Converter

1

Torque Converter to Flexplate Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Access through inspection cover. Rotate engine to access all three bolts.

Bellhousing

1

Bellhousing to Engine Block Bolts (M10)

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Usually located on lower positions of the bellhousing.
2

Bellhousing to Engine Block Bolts (M12)

M12 x 1.75
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Usually located on upper positions of the bellhousing.

Output Shaft Yoke

1

Transmission Output Shaft Yoke Bolt

M18 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Value may vary based on yoke/u-joint style. Verify specific requirements.

Cooler Line Fittings

1

Transmission Cooler Line Fittings

1/2-20 (estimated)
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new thread sealing washer. Estimated bolt size as specific size can vary slightly between manufacturers.

Extension Housing

1

Transmission Case Extension Housing Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Typically 6-8 M8 bolts. Verify specific requirements.

5.3l Engine

Torque specifications for 5.3L Engine

Cylinder Head

1

Cylinder Head Bolts

M11 x 2.0
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90° 3. 70°
Important Notes
Torque-to-yield bolts. Use the correct tightening sequence. Final angular torque is often done in 2 passes to avoid stressing the head. Consult the service manual for the correct procedure and tightening sequence.

Engine Block

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
1. 37 ft-lbs (50 N·m) 2. 80° 3. 50°
Important Notes
Torque-to-yield bolts. Use the correct tightening sequence. Consult the service manual for the correct procedure and tightening sequence. Final angular torque is often done in 2 passes to avoid stressing the caps.
2

Oil Pan Bolts

M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even sealing. Do not overtighten.
3

Timing Chain Tensioner Bolt

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the tensioner is properly positioned before tightening.

Crankshaft And Rotating Assembly

1

Connecting Rod Nuts

M9 x 1.0
Torque Specification
1. 37 ft-lbs (50 N·m) 2. 70°
Important Notes
Torque-to-yield nuts. Use the correct tightening sequence. Consult the service manual for the correct procedure and tightening sequence.
2

Flywheel Bolts

M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Apply a small amount of thread locker. Tighten in a star pattern.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M16 x 2.0
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 135°
Important Notes
Torque-to-yield bolt. Consult the service manual for the correct procedure and angle. Do not reuse this bolt.

Valve Train

1

Valve Cover Bolts

M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even sealing.
2

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the sprockets are properly aligned before tightening.
3

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper rocker arm alignment before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten in a criss-cross pattern from the center out. Do not overtighten.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten in a sequence from the center out. Verify gasket alignment before tightening.
3

EGR Valve Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper gasket alignment before tightening.
4

Throttle Body Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to ensure proper sealing. Check for vacuum leaks after installation.
5

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment to prevent fuel leaks.
6

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to ensure proper injector sealing.

Cooling System

1

Water Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten in a criss-cross pattern for even sealing. Ensure correct gasket placement.
2

Water Pump Pulley Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper pulley alignment before tightening.
3

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to prevent coolant leaks. Ensure correct gasket placement.

Ignition System

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure proper seating and electrical connection of the ignition coil.

Miscellaneous

1

Spark Plugs

M14 x 1.25
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Apply anti-seize compound sparingly to the threads. Do not overtighten.
2

Oil Filter Housing Bolt

M22 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Hand tight is typical but to avoid any ambiguity, 30ft-lbs can be used for a spin-on style filter. Ensure the sealing surface is clean.
3

Oil Drain Plug Bolt

M12 x 1.75
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Replace the crush washer each time. Do not overtighten.

6.0l Engine

Torque specifications for 6.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M11 x 2.0
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90° 3. 70°
Important Notes
Torque in sequence, first to 18 ft-lbs, then angle 90 degrees, then an additional 70 degrees. Failure to follow the specified angle sequence will result in head gasket failure.

Engine Block

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
1. 37 ft-lbs (50 N·m) 2. 70°
Important Notes
Torque in sequence, first to 37 ft-lbs, then angle 70 degrees. Proper bearing clearance is critical for engine reliability.
2

Oil Pan Bolts

M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Torque bolts evenly in a crisscross pattern. Do not over-tighten to avoid damaging the oil pan or gasket.
3

Oil Pickup Tube Mounting Bolt

M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Ensure the pickup tube is properly aligned. Do not over-tighten to avoid damage to the pickup tube bracket.

Connecting Rods

1

Connecting Rod Nuts

M9 x 1.25
Torque Specification
1. 37 ft-lbs (50 N·m) 2. 70°
Important Notes
Torque in sequence, first to 37 ft-lbs, then angle 70 degrees. Proper rod bearing clearance is critical.

Rotating Assembly

1

Flywheel Bolts

M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Torque bolts in a star pattern. Ensure flywheel is flush with crankshaft flange before tightening.
2

Crankshaft Pulley/Harmonic Balancer Bolt

M16 x 2.0
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Use a new bolt if old one is suspected of stretching. Ensure harmonic balancer is fully seated on the crankshaft.

Valve Train

1

Valve Cover Bolts

M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Torque bolts evenly to avoid leaks. Do not over-tighten.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Torque in sequence. Ensure proper rocker arm alignment before final tightening.
3

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure correct timing before tightening. Check proper sprocket and camshaft engagement.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper tensioner operation and alignment before tightening.

Intake System

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Torque bolts in a sequence starting from the center out. Proper seal is crucial for preventing vacuum leaks.
2

Throttle Body to Intake Manifold Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure proper throttle body alignment, and torque evenly to avoid air leaks.
3

EGR Valve Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper valve alignment to prevent leaks. Do not over tighten.
4

MAP Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure MAP sensor o-ring is in good condition. Do not over tighten.
5

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Torque evenly. Check for leaks after installation.
6

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Do not over-tighten. Ensure proper injector alignment.

Exhaust System

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
1. 26 ft-lbs (35 N·m) 2. 30 ft-lbs (41 N·m)
Important Notes
Torque in sequence, first to 26 ft-lbs, then 30 ft-lbs. Always torque from center outward. A two-stage torque is recommended to prevent warping.

Cooling System

1

Water Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Torque evenly in a crisscross pattern to avoid leaks. Ensure gasket is seated correctly.
2

Water Pump Pulley Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten bolts evenly. Check alignment of pulley with other pulleys.
3

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Torque bolts evenly. Do not over-tighten. Ensure thermostat is seated properly.

Accessory Drive

1

Serpentine/Accessory Drive Belt Tensioner Bolt

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper tensioner function and alignment before final tightening.
2

Drive Belt Idler Pulley Bolt

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure correct idler pulley alignment to prevent belt issues. Do not over-tighten.
3

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Check starter engagement with flywheel after installation. Ensure proper fit and alignment.
4

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alternator alignment with the accessory drive belt. Check for correct spacing and alignment.
5

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure compressor is properly aligned and belt tension is correct. Check for correct spacing and alignment.
6

Power Steering Pump Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure pump is correctly aligned and belt tension is correct.

Sensors

1

Crankshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure sensor is seated correctly. Do not over-tighten to avoid sensor damage.
2

Camshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure sensor is seated correctly. Do not over-tighten to avoid sensor damage.
3

Knock Sensor Mounting Bolt

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure sensor is properly seated. Do not over-tighten to avoid sensor damage.

Oil System

1

Oil Filter Cap Torque

N/A
Torque Specification
N/A
Important Notes
Hand tighten only. Overtightening may damage the oil filter housing and can cause leaks.
2

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new crush washer each time. Do not over-tighten, as this could damage the oil pan.

Body

Torque specifications for Body

Wheel And Tire

1

Wheel Lug Nuts

M14 x 1.5
Torque Specification
140 ft-lbs (190 N·m)
Important Notes
Ensure lug nuts are tightened in a star pattern to evenly distribute force.

Fuel System

1

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure straps are properly aligned before tightening.
2

Fuel Filler Neck Bolts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Make sure the filler neck is sealed correctly to prevent leaks.

Body Mounts

1

Body Mount Bolts

M12 x 1.75
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Torque may vary slightly depending on location; this is an estimated value. Use new bolts if reusing old bolts or if replacement is needed.

Hood And Front End

1

Hood Hinge Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure correct hood alignment when tightening.
2

Hood Latch Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Do not overtighten; ensure smooth latch operation.
3

Fender Bolts

M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Torque may vary slightly depending on material (steel or plastic); this is an estimated value.
4

Grille Mounting Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment of grille before tightening.
5

Headlight/Taillight Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Do not overtighten; these often attach to plastic housings. This is an estimated value.

Doors

1

Door Hinge Bolts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper door alignment when tightening. This is an estimated value for smaller hinge bolts.
2

Door Latch/Striker Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment and smooth door closure.

Bumpers

1

Bumper Mounting Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Torque may vary based on location and bumper type; this is an estimated value.

Interior

1

Seat Mounting Bolts

M10 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure proper seating alignment and secure mount.
2

Instrument Panel/Dashboard Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Do not overtighten; these usually secure plastic panels. This is an estimated value.
3

Steering Column Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque is critical for safety; This is an estimated value based on similar mountings.
4

Interior Trim Panel Bolts/Screws

M4 x 0.7
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
These fasteners are small and plastic; do not overtighten. This is an estimated value.

Tailgate Liftgate

1

Tailgate/Liftgate Hinge Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper alignment and smooth operation of the tailgate/liftgate when tightening.
2

Tailgate/Liftgate Latch/Striker Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure secure and reliable closure of the tailgate/liftgate.

Sunroof

1

Sunroof Mounting Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment to prevent leaks and rattles.

Side Mirrors

1

Side Mirror Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure proper mirror alignment and prevent vibration.

Brakes

Torque specifications for Brakes

Caliper Assembly

1

Caliper Mounting Bolts

M12 x 1.75
Torque Specification
80 ft-lbs (110 N·m)
Important Notes
These bolts attach the caliper directly to the mounting bracket. Ensure threads are clean.
2

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the brake hose to the caliper. Use new crush washers. Ensure no leaks are present after torquing.

Caliper Bracket

1

Caliper Mounting Bracket Bolts

M14 x 1.5
Torque Specification
129 ft-lbs (175 N·m)
Important Notes
These bolts secure the bracket to the steering knuckle. Ensure even tightening.

Rotor Attachment

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These bolts hold the rotor/drum to the hub. Tighten evenly.

Master Cylinder

1

Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secure the master cylinder. Avoid over-tightening.

Brake Lines

1

Brake Line Fittings (Hard Lines)

M10 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Flare nut style fittings. Correct torque is essential to prevent leaks.

Brake Booster

1

Brake Booster Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment and tightening.

Abs Sensors

1

Anti-Lock Brake Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten these bolts. This value is estimated based on similar components.

Drivetrain

Torque specifications for Drivetrain

Engine Flywheel

1

Flywheel Bolts

M11 x 1.25
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Apply a small amount of thread locker to the bolts before installation. Ensure flywheel mating surface is clean and free of debris.

Transmission

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the transmission is properly aligned with the engine block before tightening. Use new bolts if the old ones show signs of damage or stretching. Ensure mounting surfaces are free of debris.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten in a cross pattern. Use a new gasket for the oil pan to ensure a proper seal. Be careful not to overtighten, as this can damage the pan or gasket.
3

Input Shaft Seal Retainer Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Use a new gasket or sealant if specified. Be careful to align the retainer correctly before tightening to prevent seal damage. Estimated value based on similar component.
4

Transmission Output Shaft Flange Bolts to Driveshaft

M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
These bolts are critical for reliable power transfer. Apply thread locker. Confirm mating surfaces are clean of debris. This is specifically for the front driveshaft connection.

Drive Axles

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
118 ft-lbs (160 N·m)
Important Notes
These bolts connect the drive axle flanges to the transmission and wheel hubs. Use new bolts if the old ones are stretched or corroded. Mating surfaces should be clean and free of debris.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
177 ft-lbs (240 N·m)
Important Notes
This nut secures the CV joint to the wheel hub. Correct torque is crucial for proper wheel bearing preload. Always use a new nut for re-assembly. Never reuse an old axle nut.

Driveshaft

1

Propeller/Drive Shaft Bolts (Front and Rear)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts connect the driveshaft to the transfer case or differential flanges. Ensure the driveshaft is aligned correctly before tightening the bolts. Apply thread locker to the bolts.
2

Driveshaft Center Support Bearing Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
If applicable, these bolts secure the center support bearing to the chassis. Ensure the bearing is properly aligned before tightening. Estimated value based on similar component.

Transfer Case

1

Transfer Case Mounting Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
These bolts are essential for secure and stable attachment of the transfer case to the transmission or chassis. Ensure the mounting surfaces are clean and free from debris. Apply thread locker.
2

Transfer Case Drain/Fill Plug

M18 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a new sealing washer if available. Ensure plugs are torqued correctly to prevent leaks. Do not overtighten.

Rear Differential

1

Rear Differential Mounting Bolts

M12 x 1.75
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
These bolts attach the rear differential housing to the axle housing or chassis. Ensure the differential is properly aligned. Apply thread locker before installing.
2

Differential Drain/Fill Plug

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use new sealing washers. Correct torque ensures proper sealing to prevent leaks. Do not overtighten.
3

Ring Gear Bolts

M12 x 1.25
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
These bolts secure the ring gear to the differential carrier. Follow the torque sequence carefully, using the specified angle torque after the initial value. Ensure the mating surfaces are clean of debris.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper coil grounding. Bolts act as ground connection. Over-tightening can damage the coil housing.

Starting System

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the starter is securely mounted for proper flywheel engagement and grounding. Starter motor uses chassis as a ground point.

Charging System

1

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Maintain proper alternator alignment and grounding. The alternator housing acts as its ground point.

Battery System

1

Battery Terminal Nuts

M8 x 1.25
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure solid electrical connection. Over-tightening can damage the terminals or battery itself. Under tightening will cause resistance.

Grounding System

1

Ground Strap/Cable Bolts - Engine Block

M8 x 1.25
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Ensure good electrical contact between engine and chassis. Estimated value, verify based on bolt size.
2

Ground Strap/Cable Bolts - Body

M8 x 1.25
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Ensure good electrical contact with the body. Estimated value, verify based on bolt size.
3

Ground Strap/Cable Bolts - Chassis

M8 x 1.25
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Ensure good electrical contact with the chassis. Estimated value, verify based on bolt size.
4

Wiring Harness Ground Point Bolts

M6 x 1.0
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Ensure good electrical contact. Estimated value, verify based on bolt size.

Control Modules

1

Body Control Module (BCM) Mounting Bolts

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Ensure consistent ground and structural support. Estimated value, verify based on fastener size.
2

Powertrain Control Module (PCM/ECM) Mounting Bolts

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Ensure secure mounting and ground connection. Estimated value, verify based on fastener size.

Power Distribution

1

Fuse Box/Power Distribution Center Mounting Bolts

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Ensure solid contact for grounding and proper positioning. Estimated value, verify based on fastener size.

Lighting

1

Headlight Housing Mounting Bolts

M5 x 0.8
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Prevent housing damage. Estimated value, verify based on fastener size.
2

Taillight Housing Mounting Bolts

M5 x 0.8
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Prevent housing damage. Estimated value, verify based on fastener size.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust System

1

EGR Valve Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper seating of the EGR valve gasket before tightening. Torque bolts evenly to prevent leaks.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 10 ft-lbs (14 N·m) 2. 18 ft-lbs (25 N·m)
Important Notes
Use a proper torque sequence to prevent warping and ensure proper sealing.
3

Exhaust Manifold/Headers Bolts (Flange)

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten manifold bolts evenly to avoid flange distortion.
4

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the gasket is properly positioned before tightening. Tighten evenly to prevent leaks.
5

Upstream Oxygen (O2) Sensor

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure sensor threads are clean and apply anti-seize compound if necessary. Do not over tighten or damage sensor.
6

Downstream Oxygen (O2) Sensor

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure sensor threads are clean and apply anti-seize compound if necessary. Do not over tighten or damage sensor.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts evenly to ensure proper sealing and avoid leaks. These are usually low torque bolts.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure injectors are properly seated before tightening. These are usually low torque bolts.

Intake System

1

Mass Air Flow (MAF) Sensor Mounting Bolts/Screws

M5 x 0.8
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Use care when tightening these bolts. MAF housings are often made of plastic and can crack if over-tightened. This is an estimated value.
2

Manifold Absolute Pressure (MAP) Sensor Mounting Bolt/Screw

M5 x 0.8
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Be careful not to over tighten plastic sensors. This is an estimated value.
3

Intake Air Temperature (IAT) Sensor Mounting Bolt/Screw

M5 x 0.8
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Be careful not to over tighten plastic sensors. This is an estimated value.

Evaporative Emissions

1

Evaporative Emission (EVAP) Purge Valve Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
EVAP purge valves are often made of plastic and can easily crack. This is an estimated value.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Header to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure mating surfaces are clean and free of debris. Use a new gasket if specified. Tighten bolts in a criss-cross pattern.
2

Exhaust Manifold/Header Bolts (general)

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
These refer to any general bolts fastening parts of the manifold or header that are not directly to the cylinder head. Ensure mating surfaces are clean. Tighten bolts in a criss-cross pattern.

Exhaust Piping

1

Exhaust Pipe to Exhaust Manifold/Header Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use new gaskets if specified. Tighten bolts in a criss-cross pattern.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use new gaskets if specified. Tighten bolts in a criss-cross pattern.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use new gaskets if specified. Tighten bolts in a criss-cross pattern.

Exhaust Hangers

1

Exhaust Pipe Hanger/Bracket Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the exhaust system to prevent stress on the hangers. Estimated value, confirm with vehicle-specific manual and hardware.

Oxygen Sensors

1

Oxygen Sensor Torque

M18 x 1.5 (typical)
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Apply a small amount of anti-seize compound to the threads before installation. Do not over-tighten. Torque value is an estimated average for typical M18 sensor threads.

Flange Studs

1

Flange Stud Nuts

M10 x 1.5 (typical)
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten nuts evenly in a criss-cross pattern. These are generally torqued the same as standard bolts of similar size on the exhaust.

Fuel

Torque specifications for Fuel

Fuel Rail

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure bolts are tightened evenly to maintain proper sealing pressure.
2

Fuel Injector Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the injector is fully seated in its bore before tightening the bolts. Avoid over-tightening to prevent damage.
3

Fuel Pressure Regulator Mounting Bolts

M6 x 1.0
Torque Specification
6.6 ft-lbs (9 N·m)
Important Notes
These are usually small bolts securing the regulator to the fuel rail or tank assembly. Estimated value.

Fuel Pump

1

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the fuel pump assembly is properly seated before tightening the bolts. Tighten evenly.
2

Fuel Tank Sending Unit Lock Ring

N/A
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a suitable tool to tighten the lock ring to the specified torque. Ensure even pressure to avoid leaks.

Fuel Lines Fittings

1

Banjo Bolt Fuel Line Connections

M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Always use new crush washers when installing banjo bolts. Ensure proper alignment to prevent leaks. May require use of a crowsfoot wrench.
2

Hard-Line Fuel Fittings

M10 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment and use appropriate sealing methods for the hard-line connections to prevent leaks. May require a crowsfoot wrench. Estimated.

Fuel Tank

1

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the fuel tank is correctly positioned and supported before tightening the strap bolts. Tighten evenly to avoid distorting the tank.
2

Fuel Filler Neck Mounting Bolts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Check the filler neck seal before tightening the bolts to ensure a proper seal against the vehicle body.

Fuel Filter

1

Fuel Filter Mounting Bolts/Nuts

M8 x 1.25
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Ensure the fuel filter is correctly positioned and the mounting hardware is clean before tightening.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper bolt engagement before tightening. Over-tightening can damage the compressor or threads.

Ac Lines

1

A/C Line Fittings

Varies, typically M8 to M12
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Critical to achieve a proper seal with O-rings. Over-tightening may damage the fittings or O-rings.

Blower Motor

1

HVAC Blower Motor Mounting Screws

M5 x 0.8
Torque Specification
6 ft-lbs (9 N·m)
Important Notes
Value is estimated, typical for M5 screws into plastic. Be careful not to strip threads. Use an inch-pound torque wrench.

Control Module

1

HVAC Control Module Mounting Screws

M4 x 0.7
Torque Specification
6 ft-lbs (9 N·m)
Important Notes
Value is estimated, typical for small screws into plastic. Do not overtighten to avoid cracking the housing.

Evaporator Core

1

Evaporator Core Housing Bolts/Screws

M5 x 0.8
Torque Specification
6 ft-lbs (9 N·m)
Important Notes
Value is estimated, typical for M5 screws into plastic. Do not over-torque to avoid damaging the housing.

Condenser

1

Condenser Mounting Bolts/Screws

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secure mounting is needed to prevent damage from vibration.

Accumulator

1

Accumulator/Receiver Dryer Mounting Bolts/Screws

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secure mounting prevents vibration and misalignment.

Expansion Valve

1

Expansion Valve Bolts/Screws

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Value is estimated. These are small bolts and should not be over-torqued to avoid stripping the threads.

Heater Core

1

Heater Core Inlet/Outlet Pipe Bolts/Screws

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Value is estimated. Proper torque creates a watertight seal. Do not over-tighten.

Blend Door Actuator

1

Blend Door Actuator Mounting Screws

M4 x 0.7
Torque Specification
4 ft-lbs (6 N·m)
Important Notes
Value is estimated, typical for small screws into plastic. Over-tightening can strip the plastic housing.

Mode Door Actuator

1

Mode Door Actuator Mounting Screws

M4 x 0.7
Torque Specification
4 ft-lbs (6 N·m)
Important Notes
Value is estimated, typical for small screws into plastic. Over-tightening can strip the plastic housing.

Recirculation Door Actuator

1

Recirculation Door Actuator Mounting Screws

M4 x 0.7
Torque Specification
4 ft-lbs (6 N·m)
Important Notes
Value is estimated, typical for small screws into plastic. Over-tightening can strip the plastic housing.

Suspension

Torque specifications for Suspension

Front Suspension

1

Strut/Shock Absorber Upper Mounting Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the upper strut mount to the chassis. Ensure proper alignment before tightening.
2

Shock Absorber Lower Mount Bolt/Nut

M14 x 2.0
Torque Specification
107 ft-lbs (145 N·m)
Important Notes
Attaches the shock absorber to the lower control arm. Ensure proper alignment before tightening.
3

Upper Strut Mounting Nuts

M12 x 1.75
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Secures the upper strut assembly to the vehicle's body. Tighten in a cross pattern.
4

Upper Control Arm Mounting Bolts

M14 x 2.0
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Connects the upper control arm to the vehicle's frame. Tighten with the vehicle at ride height if possible.
5

Lower Control Arm Mounting Bolts

M14 x 2.0
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Connects the lower control arm to the frame/subframe. Tighten with the vehicle at ride height if possible.
6

Ball Joint Nut

M14 x 1.5
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Secures the ball joint to the control arm or steering knuckle. Ensure the ball joint is properly seated before tightening.
7

Steering Knuckle/Spindle Mounting Bolts

M14 x 2.0
Torque Specification
95 ft-lbs (129 N·m)
Important Notes
Bolts that connect the steering knuckle to the upper and lower control arms. Ensure proper seating and alignment.
8

Wheel Hub/Bearing Assembly Bolts

M14 x 1.5
Torque Specification
129 ft-lbs (175 N·m)
Important Notes
Secures the wheel hub/bearing assembly to the steering knuckle. Tighten in a cross pattern.

Steering System

1

Tie Rod End Nut

M12 x 1.5
Torque Specification
35 ft-lbs (48 N·m)
Important Notes
Secures the tie rod end to the steering knuckle. Ensure the tie rod end is properly seated.

Sway Bar

1

Sway Bar Link Nut

M10 x 1.5
Torque Specification
35 ft-lbs (48 N·m)
Important Notes
Connects the sway bar link to the sway bar and the strut or control arm. Tighten with the suspension at ride height.
2

Sway Bar Mounting Bracket Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (48 N·m)
Important Notes
Secures the sway bar mounting brackets to the frame. Ensure proper alignment.

Bump Stop

1

Bump Stop Mounting Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the bump stop to the frame or shock mount. Ensure bump stop is properly positioned.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the torque specification for the 2002-2006 Cadillac Escalade wheel lug nuts?

140 ft-lbs (189 Nm)

Q2

What torque wrench IS recommended for tightening Cadillac Escalade lug nuts?

A torque wrench with a range of 100-200 ft-lbs (135-270 Nm) and a 1/2-inch drive.

Q3

What IS the torque specification for the 2002-2006 Cadillac Escalade spark plugs?

18 ft-lbs (24 Nm)

Q4

What IS the torque specification for the 2002-2006 Cadillac Escalade oil drain plug?

18 ft-lbs (24 Nm)

Q5

What IS the torque specification for the 2002-2006 Cadillac Escalade transmission pan bolts?

10 ft-lbs (13 Nm)

Q6

What IS the torque specification for the 2002-2006 Cadillac Escalade differential cover bolts?

25 ft-lbs (34 Nm)

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the escalade.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Bolt Tightening Sequence for Cylinder Head

Technical procedure overview specific to Cadillac escalade

  • Clean all bolt threads and contact surfaces.
  • Apply a light coating of engine oil to the bolt threads and washers.
  • Tighten the bolts in the following sequence: 1, 3, 5, 7, 2, 4, 6, 8.
  • Tighten the bolts to the specified torque of 100 Nm (74 ft-lb).
  • Recheck the torque after 500 miles (800 km).
View full procedure
Technical Service Bulletins

Engine Bolt Torque Specifications

2003-01-01

Detailed bulletin description for Cadillac escalade

2002-2006 escalade

Resolution: Refer to the following torque specifications when tightening engine fasteners: * Main bearing cap bolts: 35 Nm (26 ft-lb) + 90 degrees * Connecting rod bolts: 39 Nm (29 ft-lb) + 90 degrees * Cylinder head bolts: 100 Nm (74 ft-lb) + 90 degrees

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Cadillac Specs. All rights reserved.

Privacy Policy Terms of Service