Cadillac Vehicle Models CT5 2020-present Torque Specifications
Cadillac Vehicle Models CT5 2020-present

Cadillac Vehicle Models CT5 2020-present Torque Specifications

Complete Cadillac Vehicle Models CT5 2020-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

10l90 Transmission

Torque specifications for 10l90 Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of transmission and use new bolts if required.

Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even gasket compression. Use a new gasket.

Drain Fill Plugs

1

Transmission Drain and Fill Plugs

M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new crush washer or O-ring to ensure proper sealing. Do not over tighten.

Drive Axle

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensure mating surfaces are clean and free of debris.

Propeller Shaft

1

Propeller/Drive Shaft Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of the drive shaft.

Bellhousing

1

Transmission Bellhousing to Engine Bolts

M12 x 1.75
Torque Specification
1. 44 ft-lbs (60 N·m) 2. 70°
Important Notes
Use new torque-to-yield bolts. Follow the specific torque sequence, then angle tightening.

Cooler Line Fittings

1

Transmission Fluid Cooler Line Fittings

M16 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use new seals where necessary to prevent leaks. Do not over-tighten.

Bellhousing Cover

1

Transmission Bellhousing Inspection Cover Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Use a new gasket if required, tighten in a criss-cross pattern.

Case Bolts

1

Transmission Case Bolts (Small)

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Internal case bolts, estimated value, tighten in a star pattern. Refer to a factory manual for specific location.
2

Transmission Case Bolts (Medium)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Internal case bolts, estimated value, tighten in a star pattern. Refer to a factory manual for specific location.
3

Transmission Case Bolts (Large)

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Internal case bolts, estimated value, tighten in a star pattern. Refer to a factory manual for specific location.

Output Flange Nut

1

Output Flange/Shaft Retaining Nut

M30 x 2.0
Torque Specification
175 ft-lbs (237 N·m)
Important Notes
Estimated value, use a new nut if required. Refer to factory manual for specific application.

Tcm Mounting

1

Transmission Control Module (TCM) Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment of TCM. Do not over-tighten.

2.0l Engine

Torque specifications for 2.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M12 x 1.75
Torque Specification
1. 18 ft-lbs (25 N·m)
Important Notes
Follow specific tightening sequence as indicated in the service manual.
2

Spark Plugs

M14 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Do not overtighten to prevent damage to cylinder head threads.
3

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)

Engine Block

1

Main Bearing Bolts

M10 x 1.5
Torque Specification
1. 37 ft-lbs (50 N·m)
Important Notes
Follow the tightening sequence as specified in the service manual.
2

Oil Pan Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Use a new gasket or sealant as specified.
3

Crankshaft Main Bolt

M14 x 1.5
Torque Specification
1. 59 ft-lbs (80 N·m) 2. 45°
Important Notes
Requires a torque angle gauge. Use new bolt.
4

Timing Cover Bolts

M6 x 1.0
Torque Specification
8.8 ft-lbs (12 N·m)
Important Notes
Use a new gasket or sealant as specified.
5

Water Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
6

Coolant Temperature Sensor

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure sensor sealing surface is clean
7

Knock Sensor Bolt

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure sensor mounting surface is clean.
8

Engine Mount Bolts (Block Side)

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)

Valve Train

1

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
May require specific sequence, refer to service manual.
3

Camshaft Bearing Cap Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Follow specific tightening sequence as indicated in the service manual.

Connecting Rods

1

Connecting Rod Nuts

M9 x 1.0
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure proper connecting rod orientation and use new nuts if specified.

Intake System

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow specific tightening sequence as indicated in the service manual.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure throttle body sealing surface is clean.
3

EGR Valve Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new gasket as specified.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)

Accessory Drive

1

Crankshaft Pulley/Harmonic Balancer Bolt

M12 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure pulley is properly aligned with crankshaft.
2

Water Pump Pulley Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
3

Serpentine/Accessory Drive Belt Tensioner Bolt

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
4

Drive Belt Idler Pulley Bolt

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)

Engine Sensors

1

Crankshaft Position Sensor (CKP) Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
2

Camshaft Position Sensor (CMP) Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)

Ignition System

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)

Lubrication

1

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use new gasket if specified.
2

Oil Filter Cap

N/A - Hand tight only
Torque Specification
N/A
Important Notes
Hand tight is sufficient for filter cap
3

Oil Filter Housing Bolt

N/A - Hand tight only
Torque Specification
N/A
Important Notes
Hand tight is sufficient for housing, ensure sealing surface is clean and gasket is in place

Valve Cover

1

Valve Cover Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Use new gasket or sealant as specified.

3.0l Engine

Torque specifications for 3.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90° 3. 90°
Important Notes
Torque in sequence. Follow the specific torque sequence as outlined in the service manual. Estimated torque-to-angle procedure included. Always use new bolts.

Crankshaft And Rotating Assembly

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
1. 37 ft-lbs (50 N·m) 2. 60°
Important Notes
Torque in sequence. Follow the specific torque sequence as outlined in the service manual. Estimated torque-to-angle procedure included.
2

Connecting Rod Nuts

M9 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 30 ft-lbs (41 N·m)
Important Notes
Torque in multiple steps. First pass to 15 ft-lbs, final pass to 30 ft-lbs.
3

Flywheel Bolts

M10 x 1.5
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Torque in sequence. Follow the specific torque sequence as outlined in the service manual.
4

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
1. 37 ft-lbs (50 N·m) 2. 90°
Important Notes
Estimated torque-to-angle procedure included. Ensure the pulley is properly seated.

Engine Block

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Torque in sequence. Use a criss-cross tightening pattern to ensure even sealing.
2

Oil Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the oil pump is properly seated against the block. Estimated value.
3

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the sensor is properly seated before tightening.
4

Knock Sensor Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Do not over-tighten the sensor. Estimated value.

Valvetrain

1

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the camshaft is in the correct position prior to tightening.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten evenly to ensure rocker arm alignment. Estimated value.
3

Valve Cover Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten in a criss-cross sequence to prevent leaks. Use a new gasket if necessary.
4

Camshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the sensor is properly seated before tightening. Estimated value.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure proper tensioner engagement. Estimated value.
2

Timing Cover Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten using a criss-cross pattern to prevent leaks. Use a new gasket or sealant.

Intake System

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten in a criss-cross sequence to ensure even pressure. Use a new gasket if necessary.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure throttle body is properly aligned. Estimated value.
3

EGR Valve Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the EGR valve is properly seated against the intake manifold. Estimated value.
4

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the fuel rail is correctly positioned and fuel injectors are seated. Estimated value.
5

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to avoid damaging the fuel injector. Estimated value.

Exhaust System

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten in a sequence from the center outwards to ensure proper sealing. Use new gasket if necessary.

Cooling System

1

Water Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the water pump is properly seated with a new gasket or sealant.
2

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure pulley is properly aligned. Estimated value.
3

Thermostat Housing Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new gasket or sealant. Estimated value.

Accessories

1

Serpentine/Accessory Drive Belt Tensioner Bolt

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper tensioner alignment. Estimated value.
2

Drive Belt Idler Pulley Bolt

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the idler pulley is properly aligned. Estimated value.

Ignition System

1

Spark Plugs

M14 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper torque to prevent compression leaks. Estimated value.
2

Ignition Coil Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the coil is properly seated. Estimated value.

Other

1

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a new crush washer. Estimated value.

Body

Torque specifications for Body

Fuel System

1

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensures proper seal and prevents fuel leaks.
2

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Critical for securing the fuel tank to the underbody.

Door System

1

Door Hinge Bolts (Body Side)

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Critical for proper door operation and alignment.
2

Door Striker Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Ensures the door latches correctly and safely.
3

Door Panel Fasteners

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the door panel to the door frame.

Body Panels

1

Fender Bolts/Fasteners

M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use 10 N·m for smaller bolts, 25 N·m for larger bolts. Confirm sizes on manual.
2

Bumper Cover Bolts/Fasteners

M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use 10 N·m for smaller bolts, 25 N·m for larger bolts. Confirm sizes on manual.

Hood System

1

Hood Hinge Bolts (Body Side)

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Critical for secure and proper hood operation.
2

Hood Latch Bolt/Fastener

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensures the hood remains securely closed.

Lighting System

1

Tail Light Housing Bolts/Fasteners

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensures secure mounting and prevents water intrusion.
2

Head Light Housing Bolts/Fasteners

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensures secure mounting and prevents water intrusion.

Interior System

1

Seat Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Vital for safety, ensuring seats are firmly in place.
2

Center Console Bolts/Fasteners

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensures proper fit and prevents rattling.
3

Dashboard Bolts/Fasteners

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensures stability, prevents vibrations, and proper placement.
4

Interior Trim Panel Fasteners/Screws

M4 x 0.7
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Ensures trim pieces are securely held without causing damage.
5

Rear View Mirror Bolt

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Maintains proper mirror position and visibility.
6

Sun Visor Screws

M4 x 0.7
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Ensures the proper operation of the visor.

Windshield System

1

Windshield Wiper Motor Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensures the proper operation of the wipers.

Brakes

Torque specifications for Brakes

Caliper

1

Brake Caliper Mounting Bolts

M12 x 1.75
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Secures the caliper to the mounting bracket. Ensure bolts are clean and threads are in good condition. Apply a thin coat of anti-seize if needed.
2

Brake Caliper Bleeder Screw

M10 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Proper torque is crucial to prevent leaks and damage. Over-tightening can damage the screw or caliper. Use a flare nut wrench to avoid rounding the bleeder.
3

Brake Pad Retaining Pin or Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Secures the brake pads in the caliper. Do not over-tighten. Ensure pins or bolts are clean. Use anti-seize if needed.
4

Brake Line Banjo Bolt

M10 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Connects the brake line to the caliper. Always use new crush washers. Over-tightening can damage threads and cause leaks.

Caliper Bracket

1

Brake Caliper Mounting Bracket Bolts

M14 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
High-stress connection. Ensure bolts are clean and threads are in good condition. May require a thread locker compound.

Rotor

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Secures the rotor to the hub for alignment during wheel installation. Do not over-tighten. Apply anti-seize if required.

Wheel

1

Wheel Lug Nuts

M14 x 1.5
Torque Specification
140 ft-lbs (190 N·m)
Important Notes
Proper torque is essential for wheel safety and brake system function. Use a star pattern to tighten.

Master Cylinder

1

Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Securely mounts the master cylinder. Ensure all bolts are clean and threads are in good condition.
2

Brake Booster Mounting Nuts/Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the brake booster to the firewall or mounting bracket. Ensure all nuts and bolts are clean and threads are in good condition.

Parking Brake

1

Parking Brake Cable Adjustment Nut

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper parking brake cable tension. Do not over-tighten. Torque may vary depending on the system.

Abs

1

ABS Sensor Mounting Bolt/Screw

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Secures the ABS sensor to the hub or knuckle. Do not over-tighten. Check for proper sensor alignment.

Proportioning Valve

1

Brake Proportioning Valve Mounting Bolt/Screw

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Secures the proportioning valve to the frame or body. Do not over-tighten. Check for proper valve alignment.

Drivetrain

Torque specifications for Drivetrain

Engine To Transmission

1

Flywheel Bolts

M12 x 1.25
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Apply thread locker. Tighten in a star pattern.
2

Transmission to Engine Block Bolts

M12 x 1.75
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Estimated value. Consult specific service manual for exact specifications.
3

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment before tightening.

Transmission

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
These bolts attach the transmission to the vehicle's frame or subframe.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten in a crisscross pattern to avoid leaks.
3

Transmission Drain and Fill Plugs

M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use new crush washers/seals. Do not overtighten.
4

Transmission Output Shaft Nut

M24 x 1.5
Torque Specification
135 ft-lbs (183 N·m)
Important Notes
Estimated value. Verify with specific service manual.

Driveshaft

1

Propeller/Drive Shaft Bolts

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of the driveshaft.

Axles And Cv Joints

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensure proper alignment of the axle before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
118 ft-lbs (160 N·m)
Important Notes
Use a new nut if recommended. Secure with locking mechanism if provided.

Differential

1

Differential Housing Bolts

M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value. Tighten in a crisscross pattern.
2

Differential Drain/Fill Plug

M18 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use a new crush washer/seal if recommended.
3

Differential Pinion Nut

M27 x 2.0
Torque Specification
1. 110 ft-lbs (149 N·m) 2. 90°
Important Notes
Final torque is achieved by torquing to value and then applying the specified angle. May require a new nut. Consult specific service manual.

Transfer Case

1

Transfer Case Housing Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value. Tighten in a crisscross pattern.
2

Transfer Case Drain/Fill Plug

M18 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use a new crush washer/seal if recommended.

Wheel Hubs

1

Wheel Hub/Bearing Bolts

M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Tighten in a star pattern for even load distribution.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper electrical contact and alignment of the coil. Over-tightening can damage the coil housing.

Starting System

1

Starter Motor Mounting Bolt

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensures secure mounting and a good electrical ground for the starter. Improper torque can cause misalignment.

Charging System

1

Alternator Mounting Bolt

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensures proper alignment and a secure electrical connection. Prevents vibrations and charging issues.

Battery Connections

1

Battery Terminal Nut

M6 x 1.0
Torque Specification
8 ft-lbs (10.8 N·m)
Important Notes
Critical for a solid electrical connection. Over-tightening can damage the battery posts, and under-tightening can cause connection issues.

Ecm Bcm

1

Engine Control Module (ECM) Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper grounding and secure mounting. Over-tightening can damage the module.
2

Body Control Module (BCM) Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper grounding and secure mounting. Over-tightening can damage the module.

Grounding Points

1

Small Ground Strap/Wire Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures a reliable electrical return path. Improper torque can lead to poor grounding.
2

Large Ground Strap/Wire Mounting Bolt

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensures a reliable electrical return path. Improper torque can lead to poor grounding.

Sensor Mounts

1

Generic Sensor Mounting Bolt (Plastic Housing)

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper mounting and grounding of sensors. Over-tightening can damage plastic housings. This is an estimated value, always refer to the specific sensor’s manufacturer specifications.
2

Generic Sensor Mounting Bolt (Metal Housing)

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper mounting and grounding of sensors. Always refer to the specific sensor’s manufacturer specifications. This is an estimated value.

Lighting

1

Headlight Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper alignment, and a good ground through the mounting brackets. Over-tightening can crack plastic housings.
2

Taillight Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper alignment and good ground. Over-tightening can crack plastic housings.

Power Distribution

1

Fuse Box/Power Distribution Box Mounting Bolt

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures secure mounting and a reliable electrical connection. Over-tightening can damage the box housing.

Wiring Harness Connections

1

Wiring Harness Connector Retaining Bolt/Screw

M3 x 0.5
Torque Specification
0.66 ft-lbs (1 N·m)
Important Notes
Secures the connector. Over-tightening can damage the connector, and under-tightening can cause a poor connection. This is an estimated value based on typical small connector screws.

Emissions Sensors

Torque specifications for Emissions_sensors

Egr System

1

EGR Valve Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure gasket is properly aligned. Apply even torque. Over-tightening may damage the valve or gasket and cause vacuum leaks.

Exhaust System

1

Exhaust Manifold/Header Mounting Bolts/Nuts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even pressure against the cylinder head. Ensure a proper gasket is used to prevent leaks. These are often studs with nuts.
2

Exhaust Manifold/Header to Cylinder Head Bolts/Nuts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even pressure against the cylinder head. These are often studs with nuts.
3

Catalytic Converter to Exhaust Pipe Bolts/Nuts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the gasket or seal is properly seated. Use new hardware when possible.
4

Pre-Catalytic Converter Oxygen Sensor

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use anti-seize compound on sensor threads. Do not overtighten, as this can damage the sensor. This is an estimated value based on common O2 sensor specifications.
5

Post-Catalytic Converter Oxygen Sensor

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use anti-seize compound on sensor threads. Do not overtighten, as this can damage the sensor. This is an estimated value based on common O2 sensor specifications.

Intake System

1

Mass Air Flow (MAF) Sensor Mounting Bolts

M5 x 0.8
Torque Specification
6 in-lbs (8 N·m)
Important Notes
Do not overtighten, as the sensor housing can be easily damaged. Use a calibrated inch-pound torque wrench.
2

Intake Air Temperature (IAT) Sensor Mounting Bolt/Screw

M4 x 0.7
Torque Specification
1.8 ft-lbs (2.5 N·m)
Important Notes
Do not overtighten, as the sensor can be easily damaged. If a threaded sensor, use a torque of 89 inch-lbs (10 N·m).

Evaporative Emissions System

1

Evaporative Emissions (EVAP) Purge Valve Mounting Bolts/Screws

M5 x 0.8
Torque Specification
6 in-lbs (8 N·m)
Important Notes
The purge valve is often made of plastic, so avoid overtightening. Use a calibrated inch-pound torque wrench.
2

Fuel Tank Pressure Sensor

M6 x 1
Torque Specification
7 in-lbs (10 N·m)
Important Notes
Do not overtighten, as this can damage the sensor or fuel tank. Ensure threads are clean and in good condition. This is an estimated value based on similar sensors.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Header to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper gasket alignment. Torque bolts evenly in a criss-cross pattern to prevent warping and ensure uniform clamping pressure.
2

Exhaust Manifold/Header Mounting Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
These bolts attach the manifold to the mounting studs or head. Ensure proper gasket alignment. Torque bolts evenly in a criss-cross pattern to prevent warping and ensure uniform clamping pressure.
3

Exhaust Pipe to Exhaust Manifold/Header Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use a new gasket if applicable. Torque bolts in an alternating sequence to ensure even pressure across the flange.

Exhaust Piping

1

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use new gaskets to ensure proper sealing. Torque bolts evenly in an alternating sequence to prevent leaks.
2

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper muffler alignment to avoid stress on the exhaust system. Tighten evenly to maintain a proper seal.
3

Exhaust Pipe Clamp Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the exhaust pipe sections are properly aligned before tightening the clamp. Tighten the bolt evenly to ensure a proper seal. Estimated value based on common exhaust clamp specifications.

Exhaust Supports

1

Exhaust Pipe Hanger/Bracket Bolts to Body/Frame

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Do not overtighten; may damage the chassis. Ensure proper alignment of the exhaust system before final tightening.

Sensors

1

Oxygen Sensor Torque

M18 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Use a torque wrench to ensure the correct torque is applied. Ensure proper sealing of the sensor by not over or under torquing. This is an average value, consult service manual for exact specification.

Fuel

Torque specifications for Fuel

Fuel Rail

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure all mating surfaces are clean. Tighten bolts evenly to prevent leaks.
2

Fuel Injector Retaining Bolts

M5 x 0.8
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure O-rings are properly seated and not damaged. Tighten gently and evenly.

Fuel Pump

1

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten bolts evenly to ensure a proper seal against the fuel tank. Check for any leaks after installation.
2

Fuel Tank Sending Unit Retaining Ring

N/A
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Estimated value. Ensure the retaining ring is properly engaged and tightened to create a secure seal. May require a specialized tool.

Fuel Filler

1

Fuel Filler Neck Mounting Bolts

M6 x 1.0
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten evenly to ensure proper alignment and prevent leaks. Check all hoses are connected before tightening the bolts.

Fuel Filter

1

Fuel Filter Mounting Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the fuel filter before tightening. Check for leaks after install.

High Pressure Fuel Pump

1

High-Pressure Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value. Tighten bolts in a cross pattern to ensure even pressure. Check for fuel leaks after installation.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the compressor is aligned properly before tightening bolts. Tighten bolts in a cross pattern to ensure even clamping force.
2

A/C Line Fittings

Vary by line, typically M10 x 1.25 or M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a flare nut wrench when applicable. Over-tightening may damage the fittings and cause leaks. Ensure O-rings or sealing surfaces are in good condition before installation. For fittings with o-rings, lightly lubricate the O-ring with refrigerant oil.
3

A/C Receiver Drier Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure mounting surfaces are clean. Bolts should be tightened evenly to avoid binding.
4

A/C Pressure Sensor Mounting

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Use care when installing the sensor. Over-tightening can damage the sensor or cause leaks. Ensure sealing surfaces are clean and the sensor is properly seated.
5

Expansion Valve Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the expansion valve is properly seated and aligned before tightening bolts. Over-tightening can damage the valve and cause leaks. Use a cross tightening pattern when multiple bolts are used to ensure proper mounting.

Ac Condenser

1

A/C Condenser Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Condenser bolts should be tightened evenly to avoid distortion and vibration. Mounting locations will vary depending on the vehicle.

Ac Evaporator

1

A/C Evaporator Core Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure the evaporator core is seated properly in its housing before securing bolts. Over-tightening can damage the core or housing.

Hvac Blower

1

HVAC Blower Motor Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts evenly to prevent vibration and noise. Ensure the blower motor is correctly seated before tightening. Mounting locations will vary depending on the vehicle.

Hvac Actuators

1

HVAC Blend Door Actuator Mounting Screws

M4 x 0.7
Torque Specification
2.9 ft-lbs (4 N·m)
Important Notes
These are small screws and can easily break the plastic housing. Tighten with care. Do not over-tighten. Actuators are very often pre-positioned before installation and can be damaged if not mounted properly.

Hvac Control

1

HVAC Control Module Mounting Bolts/Screws

M4 x 0.7
Torque Specification
3.6 ft-lbs (5 N·m)
Important Notes
Do not over-tighten, as this could damage the module housing or internal electronics. Handle the module with care and ensure connectors are properly secured. Mounting locations will vary.

Hvac Ducts

1

HVAC Duct and Housing Mounting Screws/Bolts

Vary, typically M4 x 0.7 or M5 x 0.8
Torque Specification
2.9 ft-lbs (4 N·m)
Important Notes
Do not over-tighten as these are generally plastic components with plastic mounting screws. Use care to not strip the plastic threads. Mounting locations and sizes may vary. Use 2.9 ft-lbs (4 Nm) for plastic mounting screws in most locations.

Suspension

Torque specifications for Suspension

Front Suspension

1

Strut Upper Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
These bolts secure the top of the strut assembly to the vehicle's frame. Ensure proper alignment during installation.
2

Lower Shock Mounting Bolt

M14 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
This bolt secures the lower end of the shock absorber to the suspension knuckle or control arm. This applies to vehicles equipped with shock absorbers instead of a strut.
3

Lower Control Arm Frame Bolts

M14 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
These bolts secure the lower control arm to the vehicle's frame or subframe. They are critical for suspension geometry.
4

Lower Control Arm Ball Joint to Knuckle Bolts

M12 x 1.75
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
These bolts connect the lower control arm ball joint to the steering knuckle. Proper torque is crucial for maintaining correct suspension geometry.
5

Upper Control Arm Ball Joint Nut

M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
This nut secures the upper control arm ball joint to the steering knuckle. Ensure proper seating before tightening.
6

Tie Rod End Nut

M14 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
This nut secures the tie rod end to the steering knuckle. Ensure proper alignment to maintain steering geometry.
7

Steering Knuckle/Spindle Bolts/Nuts to Lower Control Arm

M14 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
These fasteners connect the knuckle/spindle to the lower control arm, it is critical to follow the torque spec.
8

Wheel Hub/Bearing Retaining Nut/Bolt (Front)

M24 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
This nut/bolt secures the wheel hub/bearing assembly to the knuckle. Proper torque is critical for bearing preload and wheel safety. Ensure proper tightening procedure for correct preload.
9

Wheel Speed Sensor Bolt

M6 x 1.0
Torque Specification
7.5 ft-lbs (10 N·m)
Important Notes
These bolts secure the wheel speed sensor to the knuckle. Overtightening can damage the sensor; use inch-lbs.

Sway Bar

1

Sway Bar Link Nut

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
These nuts secure the sway bar links to the sway bar and strut/control arm. Ensure proper alignment to avoid binding.
2

Stabilizer Bar (Sway Bar) Frame Mount Bracket Bolts

M10 x 1.5
Torque Specification
45 ft-lbs (60 N·m)
Important Notes
These bolts secure the sway bar mounting brackets to the frame or subframe. Ensure the bushings are properly seated.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque for the lug nuts on a 2020-Present Cadillac CT5?

140 lb-ft (190 Nm)

Q2

What type of torque wrench should I use for critical suspension components on my CT5?

Use a high-quality click-type torque wrench that has been calibrated to ensure accuracy.

Q3

Can I use anti-seize lubricant on the threads of spark plugs when installing them?

Yes, applying a small amount of anti-seize lubricant to the threads of spark plugs IS acceptable to prevent seizing and aid in removal during future maintenance.

Q4

What IS the torque specification for the oil drain plug on a 2021 Cadillac CT5?

25 lb-ft (34 Nm)

Q5

How do I ensure proper torque application when replacing brake calipers?

Always refer to the specific torque specifications provided by the manufacturer. Use a torque wrench and gradually apply torque to reach the desired value. Double-check the tightness of the bolts after the initial torque application.

Q6

What are some common torque mistakes that should be avoided?

Over-tightening, under-tightening, using the wrong torque wrench, not following the correct tightening sequence, and not lubricating threads as specified.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the ct5.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Bolt Tightening Procedure for Cadillac ct5

Overview of general bolt tightening procedures and torque specifications for the ct5.

  • Clean all mating surfaces and threads.
  • Apply anti-seize or threadlocker if specified.
  • Tighten fasteners to the specified torque values using a digital torque wrench in the correct order.
  • Follow all safety precautions and consult the service manual for specific component instructions.
  • Refer to the technical bulletins for any updates or changes.
View full procedure
Technical Service Bulletins

Front Suspension Noise During Braking - Tighten Brake Caliper Bolts (2020-2022 ct5)

2022-07-01

Addresses excessive noise coming from the front suspension during braking due to loose brake caliper bolts. Includes torque specifications and tightening procedure.

2020-2022 ct5

Resolution: Inspect and tighten the brake caliper mounting bolts to 120 Nm (89 ft-lb).

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Cadillac Specs. All rights reserved.

Privacy Policy Terms of Service